PCI-9810 SLS [System Logic Semiconductor], PCI-9810 Datasheet - Page 2

• Manufacturer Part Number: PCI-9810
• Description: 4-CH 10/12-bit 20 MS/s Simultaneous-Sampling Analog Input Cards
• Manufacturer: SLS [System Logic Semiconductor]

Specifications
Analog Input
Triggering
Number of channels: 4 single-ended
Resolution
Maximum sampling rate: 20 MS/s
Input signal ranges, impedance and overvoltage
protection
Accuracy: ±1.5 % typical
DNL: ±0.4 LSB typical, ±1.0 LSB maximum
INL: ±1.9 LSB typical
Input coupling: DC
Trigger sources: software, analog and digital
trigger (5 V/TTL compatible)
Trigger modes:
software-trigger, pre-trigger, post-trigger,
middle-trigger & delay trigger
FIFO buffer size
Data transfers: bus mastering DMA
Analog triggering
Digital triggering
Input Range
12-bit (PCI-9812 and PCI-9812A)
10-bit (PCI-9810)
32k samples (PCI-9810 & PCI-9812)
128k samples (PCI-9812A)
Modes:
pre-trigger, post-trigger, middle-trigger,
delay-trigger
Source: CH0, CH1, CH2 and CH3
Slope: rising/falling
Coupling: DC
Trigger sensitivity:
256 steps in full-scale voltage range
Modes:
pre-trigger, post-trigger, middle-trigger,
delay-trigger
Source: external digital trigger
Slope: rising edge
Compatibility: 5 V/TTL
Minimum pulse width: 25 ns
±1 V
±5 V
Impedance
1.25 kΩ
15 MΩ
Input
50 Ω
50 Ω
Overvoltage
protection
±10 V
±2 V
External Sine Wave Clock
External Digital Clock
Digital Input
General Specifications
Input coupling: AC
Input impedance: 50 Ω
Input frequency: 300 kHz to 40 MHz
Input range: 1.0 to 2.0 V
Overvoltage protection: 2.5 V
Input coupling: DC
Input impedance: 50 Ω
Compatibility: 5 V/TTL
Input frequency: 20 kHz to 40 MHz
Overvoltage protection:
diode clamping, -0.3 V to +5.3 V
Number of channels: 3
Compatibility:
5 V/TTL with 10 KΩ pull down resistors
Overvoltage protection:
Diode clamping, -0.3 V to +5.3 V
Data transfers:
Dimensions (not including connectors)
173 mm x 108 mm
bus mastering DMA with A/D samples
I/O connector
Operating temperature: 0 to 50 °C
Storage temperature: -20 to 80 °C
Relative humidity: 5 to 95 %, noncondensing
Power requirements
BNC x 5
10-pin ribbon male
PCI-9812
PCI-9812A
PCI-9810
Device
*
All specifications are subject to change without further notice.
1.4 A typical
1 A typical
pp
+5 V
pp
PCI High Speed Digitizer
PCI-9810
4-CH 10-bit 20 MS/s Simultaneous-Sampling
Analog Input Card
PCI-9812
4-CH 12-bit 20 MS/s Simultaneous-Sampling
Analog Input Card
PCI-9812A
4-CH 12-bit 20 MS/s Simultaneous-Sampling
Analog Input Card with 128k-sample A/D
FIFO
Ext. Sine Wave CLK
JP1: External Digital Clock, Digital
J1-J5: Analog Inputs & External
Ext. Digital TRIG
Ext. Digital CLK
Ordering Information
Trigger & Digital Inputs
Pin Assignment
Pin Assignment
Sine Wave Clock
CH0
CH1
CH2
CH3
DI0
DI1
DI2
1
3
5
7
9
1
2
3
4
5
10
2
4
6
8
www.adlinktech.com
Shield: GND
Shield: GND
Shield: GND
Shield: GND
Shield: GND
GND
GND
GND
GND
GND
5
5-4
1
10
11
12
3
6
7
8
9
4
Software
Solutions
2
PXI/
CompactPCI
Platforms
PXI-Based
Instruments
PXI/
CompactPCI
Modules
PCI DAQ
Cards
PCI DIO
Cards
PC/104-Plus
Products
ISA DAS/
DIO Cards
Wiring
Termination
Boards
Motion
Control
Cards
Machine
Vision
Products
Remote I/O
Modules