PI5C16210AE Pericom Semiconductor, PI5C16210AE Datasheet - Page 3

• Manufacturer Part Number: PI5C16210AE
• Description: IC 20-BIT BUS SW 2PORT 48-TSSOP
• Manufacturer: Pericom Semiconductor
• Type: Bus Switchr

Specifications of PI5C16210AE

• Circuit: 10 x 1:1
• Independent Circuits: 2
• Voltage Supply Source: Single Supply
• Voltage - Supply: 4 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 48-TSSOP
• Number Of Bits: 20
• Number Of Elements: 2
• Technology: CMOS
• High Level Output Current: -120mA
• Low Level Output Current: 120mA
• On Resistance: 14Ohm
• Package Type: TSSOP
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 4V
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Pin Count: 48
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output High, Low: -
• Lead Free Status / Rohs Status: Compliant

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device.
2. Typical values are at Vcc = 5.0V, +25°C ambient.
3. Per TTL driven input (V
4. This current applies to the control inputs only and represent the current required to switch internal capacitance at the specified
Switching Characteristics over Operating Range
Notes:
1. See test circuit and wave forms.
2. This parameter is guaranteed but not tested on Propagation Delays.
3. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load
Power Supply Characteristics
Parameters Description
Parameters
frequency. The A and B inputs generate no significant AC or DC currents as they transition. This parameter is not tested, but is
guaranteed by design.
capacitance. The time constant for the switch alone is of the order of 0.25ns for 50 pF load. Since this time constant is much smaller
than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the
bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the
load on the driven side.
I
ΔI
I
CC
CCD
t
t
t
t
t
t
PLH
PHL
PZH
PZL
PHZ
PLZ
CC
06-0230
Quiescent Power
Supply Current
Supply Current per
Input @ TTL HIGH
Supply Current per
Input per MHz
Description
Propagation Delay
Ax to Bx, Bx to Ax
Bus Enable Time
X
Bus Disable Time
X
OE to Ax or Bx
OE to Ax or Bx
IN
(4)
= 3.4V, control inputs only); A and B pins do not contribute to Icc.
(2,3)
Conditions
C
R
L
L
= 500-ohm
= 50 pF
V
V
V
A and B Pins Open
Control Input Toggling
50% Duty Cycle
CC
CC
CC
= Max.
= Max.
= Max.,
(1)
Test Conditions
Min
Vcc = 5V ±0.5V
1.5
1.5
3
Max
0.25
6.5
5.5
(1)
V
V
PI5C16210
IN
IN
= GND or V
= 3.4V
Min
(3)
V
CC
CC
= 4V
Max
0.25
6.3
5.5
Min.
20-Bit, 2-Port Bus Switch
Unit
ns
ns
ns
Typ
0.1
(2)
PS8140B
Max.
0.25
2.5
10
PI5C16210
Units
MHz
mA/
mA
μA
08/18/05