HV830 Supertex, HV830 Datasheet
![no-image](/images/manufacturer_photos/0/6/642/supertex_sml.jpg)
HV830
Manufacturer Part Number
HV830
Description
SOP8
Manufacturer
Supertex
Specifications of HV830
Date_code
02+
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HV830LG-G
Manufacturer:
Supertex
Quantity:
1 988
Absolute Maximum Ratings*
Supply Voltage, V
Output Voltage, V
Operating Temperature Range
Storage Temperature Range
Power Dissipation
Note:
*All voltages are referenced to GND.
Ordering Information
Features
❏ Processed with HVCMOS
❏ 2.0V to 9.5V operating supply voltage
❏ DC to AC conversion
❏ 200V peak-to-peak typical output voltage
❏ Large output load capability – typically 50nF
❏ Permits the use of high-resistance elastomeric lamp
❏ Adjustable output lamp frequency to control lamp color,
❏ Adjustable converter frequency to eliminate harmonics and
❏ Enable/disable function
❏ Low current draw under no load condition
❏ Very low standby current – 30nA typical
Applications
❏ Handheld personal computers
❏ Electronic personal organizers
❏ GPS units
❏ Pagers
❏ Cellular phones
❏ Portable instrumentation
11/12/01
Supertex Inc. does not recommend the use of its products in life support applications and will not knowingly sell its products for use in such applications unless it receives an adequate "products liability
indemnification insurance agreement." Supertex does not assume responsibility for use of devices described and limits its liability to the replacement of devices determined to be defective due to
workmanship. No responsibility is assumed for possible omissions or inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications, refer to the
Supertex website: http://www.supertex.com. For complete liability information on all Supertex products, refer to the most current databook or to the Legal/Disclaimer page on the Supertex website.
connectors
lamp life, and power consumption
optimize power consumption
Device
HV830
Cs
DD
Input Voltage
2.0V to 9.5V
®
technology
High Voltage EL Lamp Driver
8-Lead SO
HV830LG
-65°C to +150°C
-25°C to +85°C
-0.5V to +120V
-0.5V to +10V
Package Options
400mW
1
HV830X
Die
General Description
The Supertex HV830 is a high-voltage driver designed for driving
EL lamps of up to 50nF. EL lamps greater than 50nF can be
driven for applications not requiring high brightness. The input
supply voltage range is from 2.0V to 9.5V. The device uses a
single inductor and a minimum number of passive components.
The nominal regulated output voltage that is applied to the EL
lamp is ±100V. The chip can be enabled by connecting the
resistors on R
connected to GND.
The HV830 has two internal oscillators, a switching MOSFET,
and a high-voltage EL lamp driver. The frequency for the switch-
ing converter MOSFET is set by an external resistor connected
between the R
driver frequency is set by an external resistor connected be-
tween R
connected between the L
capacitor is connected between C
connected between V
The switching MOSFET charges the external inductor and
discharges it into the C
increase. Once the voltage at C
100V, the switching MOSFET is turned OFF to conserve power.
The outputs V
switched in opposite states to achieve 200V peak-to-peak across
the EL lamp.
Pin Configuration
EL-osc
R
V
SW-osc
C
DD
L
A
SW-osc
pin and the V
SW-osc
s
x
and V
1
2
3
4
pin and the supply pin V
A
and R
B
s
and V
are configured as an H-bridge and are
capacitor. The voltage at C
x
and V
SO-8
EL-osc
B
DD
.
s
pin. An external inductor is
DD
to V
S
reaches a nominal value of
and GND. The EL lamp is
pins. A 0.01µF to 0.1µF
DD
8
7
6
5
and disabled when
R
V
V
GND
HV830
DD
A
B
EL-osc
. The EL lamp
s
will start to