HGLM-1063 HP [Agilent(Hewlett-Packard)], HGLM-1063 Datasheet
HGLM-1063
Related parts for HGLM-1063
HGLM-1063 Summary of contents
Page 1
... HGLM-1063 The HGLM-1063 is intended for use in building adapter cards (or equivalent devices) as shown in Figure 1. The HGLM-1063 pro- vides complete FC-0 functionality. The HPFC-5000 provides the FC-1 through FC-4 functions and interfaces directly to the HGLM- 1063. Finally, a bus gasket is used to connect the HPFC-5000 to the specific system bus in use ...
Page 2
... Link Acquisition and Power Up The following discussion assumes the HGLM-1063 is connected in a full duplex point to point link as shown in Figure 3. When initially applying power to the HGLM- 1063, the Transmit Byte Clock must start no later than 5 msec after the +5 volt supply reaches the +4 volt level ...
Page 3
... TRANSMITTER I.C. DATA BYTE 1 Tx[10:19] EWRAP -LZON Tx_SI TBC PHOTODIODE ASSEMBLY FIBER INPUT EN_CDET -LCK_REF Figure 2. HGLM-1063 Functional Block Diagram. CLOCK (TBC) Tx ENCODED DATA HGLM1 ENCODED DATA Rx CLOCK (RBC[0:1]) Figure 3. Full Duplex Point to Point Link. H HGLM-1063 780 nm GLM Module CDRH21 CFR(J) Compilant Class 1 Laser Product 09 Nov ...
Page 4
... Figure 3 for proper operation. The Open Fiber Control System (OFCS) of the HGLM-1063 deactivates the laser signal whenever there is an interruption or loss of signal of either laser drive circuit. For example, in Figure 3, if Path ...
Page 5
... Connection of the HGLM-1063 to a non-approved optical source, operating above the recommended absolute maxi- mum conditions (especially power supply) or operating the HGLM-1063 in a manner inconsistent with its design and function may result in hazardous radiation exposure and may be considered an act of modifying or manufacturing a laser product. The person(s) ...
Page 6
... R1.6 TYP. 0 ELECTRICAL TRACE PLACEMENT 28.85 24.13 AXIS MIN. 2.94 SOCKET A20 ACCOMODATES A PIN SPEC'D 0.46 ± 0.05 0 Figure 6. Host PCB Layout for Mounting the HGLM-1063. HGLM-1063 Pin Assignments Pin Name Pin A01 +SO B01 A02 gnd B02 A03 V B03 CC A04 ...
Page 7
... HGLM-1063 Signal Definitions Symbol Signal Name TX[00:19] Transmit Data TBC Transmit Byte Clock EWRAP Enable Wrap/Enable STROP_ID -LCKREF Lock to Reference TX_SI Transmit SI EN_CDET Enable Comma Detect/STROB_ID clock SI Serial Data In RX[00:19] Receive Data RBC[0] Receive Byte Clock 0 RBC[1] Receive Byte Clock 1 COM_DET Comma Detect ...
Page 8
Transmit Byte Clock Requirements + 4 5 Symbol f Nominal Frequency F Frequency Tolerance (for Fibre Channel Compliance) tol Symm Symmetry (Duty Cycle) Jpe Positive Edge Jitter ...
Page 9
Timing Specifications + 4 5 Symbol t Decode 1 Time Dcd_1 t Decode 2 Time Dcd_2 t Decode 3 Time Dcd_3 Transmitter t Transmit Data Setup Time ...
Page 10
TBC Tx[00:19] DATA DATA Figure 7. Transmit Byte Clock and Data Timing Relationships ...