54ABT646E-QML NSC [National Semiconductor], 54ABT646E-QML Datasheet
54ABT646E-QML
Related parts for 54ABT646E-QML
54ABT646E-QML Summary of contents
Page 1
... MIL-STD-883, Method 5004 Quality Conformance Inspection MIL-STD-883, Method 5005 MICROCIRCUIT DATA SHEET Original Creation Date: 08/25/95 Last Major Revision Date: 03/19/97 Data on the bus will be clocked into the In the transceiver mode, NS Part Numbers 54ABT646E-QML * 54ABT646J-QML ** 54ABT646W-QML *** Subgrp Description 1 Static tests at 2 Static tests at 3 ...
Page 2
MN54ABT646-X REV 0B0 Features - Independent registers for A and B buses. - Multiplexed real-time and stored data and B output sink capability of 48 mA, source capability Guaranteed latchup protection - High impedance ...
Page 3
MN54ABT646-X REV 0B0 (Absolute Maximum Ratings) (Note 1) Vcc Pin Potential to Ground Potential Input Voltage (Note 2) Input Current (Note 2) Voltage Applied To Any Output In the Disabled or Power-Off State In The High State Current Applied To ...
Page 4
MN54ABT646-X REV 0B0 Electrical Characteristics DC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) DC: 4.5V to 5.5V Temp Range: -55C to 125C SYMBOL PARAMETER ICCH Supply Current VCC=5.5V, VINH=5.5V, VINL=0.0V ICCL Supply Current VCC=5.5V, ...
Page 5
MN54ABT646-X REV 0B0 Electrical Characteristics DC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: 4.5V to 5.5V Temp Range: -55C to 125C SYMBOL PARAMETER VID Input Leakage VCC=0.0V, IID=1.9uA, VINL=0.0V Test VCD Input Clamp ...
Page 6
MN54ABT646-X REV 0B0 Electrical Characteristics AC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) AC: CL=50pF RL=500 OHMS TRISE/TFALL = 3.0nS SYMBOL PARAMETER tpHL3 Propagation Delay VCC=5.0V @25C, VCC=4.5V & 5.5V @-55C/125C tpZL1 Output Enable ...
Page 7
MN54ABT646-X REV 0B0 Electrical Characteristics AC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) AC: CL=50pF RL=500 OHMS TRISE/TFALL = 3.0nS SYMBOL PARAMETER ts (H/L) Setup Time HIGH or LOW th (H/L) Hold Time HIGH ...
Page 8
MN54ABT646-X REV 0B0 Graphics and Diagrams GRAPHICS# E28ARD LCC (E), TYPE C, 28 TERMINAL(P/P DWG) J24FRG CERDIP (J), 24LD, .300 CENTERS (P/P DWG) W24CRE CERPACK (W), 24 LEAD (P/P DWG) See attached graphics following this page. MICROCIRCUIT DATA SHEET DESCRIPTION ...
Page 9
MN54ABT646-X REV 0B0 Revision History Rev ECN # Rel Date 0B0 M0002947 10/05/98 Originator Changes Bill Petcher Changed MDS MN54ABT646-X REV 0A0 0B0 9 MICROCIRCUIT DATA SHEET to MN54ABT646-X REV ...