SLIN-20F1A0 BEL [Bel Fuse Inc.], SLIN-20F1A0 Datasheet
SLIN-20F1A0
Related parts for SLIN-20F1A0
SLIN-20F1A0 Summary of contents
Page 1
... Typical Current Efficiency 20 A 90.8% 4--- Wide input voltage range (2.4-5.5V) 5--- Wide output voltage range (0.6-3.63V) 6--- Enable, active high, change “0” to “L” means active low = 2.4Vdc-5.5Vdc) and provide a IN Features Model Number Model Number Active High Active Low SLIN-20F1A0 SLIN-20F1AL www.belfuse.com 1 ...
Page 2
NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Absolute Maximum Ratings Parameter Continuous Input Voltage Sequencing Voltage Operating Ambient Temperature Storage Temperature Note: Stresses in excess of the ...
Page 3
NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Output Specifications Parameter Output Voltage Set Point Output Voltage Adjustment Range Remote Sense Range Output Regulation (for V ≥ 2.5Vdc) ...
Page 4
NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 General Specifications Parameter Efficiency Vo=0.6V Vo=1.2V Vo=1.8V Vo=2.5V Vo=3.3V Switching Frequency Over Temperature Protection Sequencing Delay time Tracking Accuracy Power-Up: ...
Page 5
NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Efficiency Data Vin=5. OUTPUT CURRENT, I Vo=0. Vin=5.5V 85 ...
Page 6
NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Thermal Derating Curves 1m/s 2m/s (200LFM) (400LFM ...
Page 7
NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Ripple and Noise Waveforms TIME, t (1μs/div) Vin=3.3V, Vo=0.6V Io,max TIME, t (1μs/div) Vin=3.3V, Vo=1.8V Io,max ...
Page 8
NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Transient Response Waveforms TIME, t (100μs /div) Transient Response to Dynamic Load Change from 0% 50% to 0%. Vin=3.3V, Vo=0.6V ...
Page 9
NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Startup Time TIME ms/div) Start-up Using On/Off Voltage (I TIME ms/div) Start-up Using On/Off Voltage (I ...
Page 10
NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Startup Time (continued) TIME ms/div) Start-up Using Input Voltage (V IN Vo=0.6V TIME ms/div) Start-up Using ...
Page 11
NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Test Configurations Input Reflected Ripple Current Test Setup. TO OSCILLOSCOPE NOTE: Measure input reflected ripple current with a simulated Output ...
Page 12
... Output Voltage (Vdc) Output Filtering The SLIN-20F1Ax modules are designed for low output ripple voltage and will meet the maximum output ripple specification with 0.1 µF ceramic and 10 µF ceramic capacitors at the output of the module. However, additional output filtering may be required by the system designer for a number of reasons. First, there may be a need to further reduce the output ripple and noise of the module ...
Page 13
... Active High Signal High (Unit On) The SLIN-20F1Ax modules feature an On/Off pin for remote On/Off operation. Two On/Off logic options are available. In the Positive Logic On/Off option, the module turns ON during a logic High on the On/Off pin and turns OFF during a logic Low. With the Negative Logic On/Off option, the module turns OFF during logic High and ON during logic Low ...
Page 14
NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Remote On/Off (cont.) For negative logic On/Off modules, the circuit configuration is shown in Figure B on the next page. ...
Page 15
... December 2, 2010 Output Voltage Programming The output voltage of the SLIN-20F1Ax module can be programmed to any voltage from 0.6dc to 3.63Vdc by connecting a resistor between the Trim and GND pins of the module. voltage set point depending on the input voltage. These are shown in the Output Voltage vs. Input Voltage Set Point Area plot in the figure below ...
Page 16
... December 2, 2010 Remote Sense The SLIN-20F1Ax power modules have a Remote Sense feature to minimize the effects of distribution losses by regulating the voltage at the SENSE pin. The voltage between the SENSE pin and VOUT pin must not exceed 0.5V. Note that the output voltage of the module cannot exceed the specified maximum value. This includes the voltage drop between the SENSE and Vout pins ...
Page 17
... Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Output Voltage Sequencing The SLIN-20F1Ax modules include a sequencing feature that enables users to implement various types of output voltage sequencing in their applications. This is accomplished via an additional sequencing pin. When not using the sequencing feature, either tie the SEQ pin to V When an analog voltage is applied to the SEQ pin, the output voltage tracks this voltage until the output reaches the set-point voltage ...
Page 18
... Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 TM Tunable Loop The SLIN-20F1Ax modules have a new feature that optimizes transient response of the module called Tunable TM Loop . External capacitors are usually added to the output of the module for two reasons: to reduce output ripple and noise and to reduce output voltage deviations from the steady-state value in the presence of dynamic load current changes ...
Page 19
NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Table 3 .Recommended values of R with Vin=5V. 3.3V Vo 2x47μ 330μF Co 2x330μF Polymer Cap Polymer Cap ...
Page 20
NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Thermal Considerations Power modules operate in a variety of thermal environments; however, sufficient cooling should always be provided to help ...
Page 21
NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Example Application Circuit Requirements: Vin: 3.3V Vout: 1.8V Iout: 15A max., worst case load transient is from 10A to 15A ...
Page 22
NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Mechanical Outline Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • ...
Page 23
NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Mechanical Outline (continued) Recommended Pad Layout Dimensions are in millimeters and (inches). Tolerances: x.x mm ± 0.5 mm (x.xx in. ...
Page 24
... NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Packaging Details The SLIN-20F1Ax modules are supplied in tape & reel as standard. All Dimensions are in millimeters and (in inches). Reel Dimensions: Outside Dimensions: 330.2 mm (13.00’’) Inside Dimensions: 177.8 mm (7.00”) Tape Width: 44.00 mm (1.73” ...
Page 25
... Surface Mount Information Pick and Place The SLIN-20F1Ax modules use an open frame construction and are designed for a fully automated assembly process. The modules are fitted with a label designed to provide a large surface area for pick and place operations. The label meets all the requirements for surface mount processing, as well as safety standards, and ...
Page 26
NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /20 A Output December 2, 2010 Storage and Handling The recommended storage environment and handling procedures for moisture-sensitive surface mount packages is detailed in J-STD-033 Rev. ...