MPM-05 MPD [MicroPower Direct, LLC], MPM-05 Datasheet - Page 2

• Manufacturer Part Number: MPM-05
• Description: Compact, 5W PC Mount Single, Dual & Triple Out AC/DC Power Supplies
• Manufacturer: MPD [MicroPower Direct, LLC]

Model Selection Guide
Notes:
1. Load regulation is measured for an output change of 10% to 90% at nominal input
2. The MPM-05 series is specifi ed for operation over the wide operating temperature
3. Single output models are approved to EN60950. Approval for other models is pending.
4. It is recommended that a fuse be used on the input of a power supply for protection.
Mechanical Dimensions
Notes:
•
•
MPM-05S-03
MPM-05S-05
MPM-05S-12
MPM-05S-15
MPM-05S-24
MPM-05D-05
MPM-05D-12
MPM-05D-15
MPM-05T-0505
MPM-05T-0512
MPM-05T-0515
MPM-05T-0524
All dimensions are typical in inches (mm)
Tolerance x.xx =
line. For multiple output models, the loads are balanced.
range of -20°C to +55°C without derating. For operation over +55°C, derate the
power linearly by 3.75%/°C from +55°C to +70°C.
For the MPM-05 series, a 1A/250 VAC slow blow should be used.
Number
Model
±
115
0.01 (
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
292 Page Street Ste D Stoughton, MA 02072
Current
MicroPower Direct
Pin Connections
VAC
±
Pin
Input
1
2
3
4
5
6
7
8
0.25)
230
AC-Ground AC-Ground AC-Ground
AC-Neutral AC-Neutral AC-Neutral
0.07
0.07
0.07
0.07
0.07
0.07
0.07
0.07
0.07
0.07
0.07
0.07
(A)
AC-Line
No Pin
No Pin
No Pin
Single
+Vo 1
-Vo 1
VAC
Voltage
(VDC)
+12.0
+15.0
12.0
15.0
24.0
+5.0
www.micropowerdirect.com
3.3
5.0
5.0
5.0
5.0
5.0
Common
AC-Line
No Pin
No Pin
+Vo 1
-Vo 2
Dual
+0.50
+0.21
+0.16
Output 1
Typ.
1.00
1.00
0.42
0.33
0.23
0.90
0.70
0.70
0.70
Current
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±2.0%
±2.0%
±2.0%
±3.0%
±3.0%
±3.0%
±3.0%
Common
Load
Reg.
AC-Line
(Vout 1)
(A)
Triple
+Vo 1
+Vo 2
-Vo 1
-Vo 2
Over Volt.
Protection
(VDC)
•
20.0
20.0
30.0
20.0
20.0
6.5
6.5
6.5
6.5
6.5
6.5
6.5
TEL: [phone]
Voltage
(VDC)
+12.0
+15.0
+24.0
-12.0
-15.0
+5.0
-5.0
Typical Connection
Typical Component Values
Notes:
1. C1, C3 and C5 are high frequency, low resistance electrolytic capacitors.
Vout
12.0
15.0
24.0
Refer to the suppliers specifi cations for capacitance/current ratings.
3.3
5.0
Output 2
+0.10 ±5.0%
+0.10 ±5.0%
+0.08 ±5.0%
+0.05 ±5.0%
Typ.
-0.50 ±2.0%
-0.21 ±2.0%
-0.16 ±2.0%
Current
•
330 ~ 1,000 µF/16V
330 ~ 1,000 µF/16V
FAX: [phone]
Load
Reg.
(Vout 2)
(A)
220 µF/25V
220 µF/25V
120 µF/35V
C1, C3, C5
Over Volt.
Protection
(VDC)
20.0
20.0
6.5
2. Voltage derating on all capacitors should be
3. C2, C4 and C6 eliminate high frequency noise.
4. The TVS is recommended to protect load
80% or higher.
circuitry in the event of a module failure.
•
Voltage
0.1 µF/50V
C2, C4, C6
(VDC)
Ceramic
-12.0 -0.10 ±5.0%
-15.0 -0.08 ±5.0%
-24.0 -0.05 ±5.0%
E-Mail: [e-mail]
Output 3
-5.0 -0.10 ±5.0%
Typ.
Current
Slow Blow
(Vout 3)
250 VAC
Fuse
1A/
Load
Reg.
(A)
P6KE6.8A
P6KE6.8A
Effi ciency
P6KE16A
P6KE20A
P6KE33A
(%, Typ)
TVS
76
76
76
76
76
76
76
76
76
76
76
76