LA72715V SANYO [Sanyo Semicon Device], LA72715V Datasheet
LA72715V
Related parts for LA72715V
LA72715V Summary of contents
Page 1
... Ordering number : ENA0982A LA72715V LA72715VA Overview JPN MTS (Multi Channel Television Sound) Decoder IC Features • With SIF circuit, alignment-free* STEREO channel separation base band signal input mode, separation is adjusted by input level. • Three slave-addresses are prepared. • The maximum output level is as large as 4.2dBV. ...
Page 2
... JCH1 Just Clock output Low voltage JCL1 Max Output level MOL1 EXTERNAL input level EXTIN1 LA72715V, 72715VA Conditions Conditions No signal, Inflow current at pin 1kHz, 100% Mod, Pre-emphasis OFF fm = 1kHz, 100% Mod, Pre-emphasis OFF fm = 1kHz, 100% Mod, Pre-emphasis OFF fm = 10kHz/1kHz, 100% Mod, 15kHz LPF ...
Page 3
... JCH2 Just Clock output Low voltage JCL2 Max Output level MOL2 EXTERNAL input level EXTIN2 LA72715V, 72715VA Conditions No signal, Inflow current at pin 4.5MHz fm = 1kHz, 100% Mod, Pre-emphasis OFF fm = 1kHz, 100% Mod, Pre-emphasis OFF fm = 1kHz, 100% Mod, Pre-emphasis OFF fm = 10kHz/1kHz, 100% Mod, 15kHz LPF ...
Page 4
... Package Dimensions unit : mm (typ) 3175C 7 0.65 0.15 (0.33) 0.22 SANYO : SSOP24(275mil) LA72715V, 72715VA Package Dimensions unit : mm (typ) [LA72715V] 3287 6 0.5 (0.5) [LA72715VA 0.22 0.15 SANYO : SSOP24(225mil) No.A0982-4/12 ...
Page 5
... Recommended constant value 0.0033µF + 470kΩ ( values when tested) (2*): Recommended matching resistor value R1=1kΩ, R2=1kΩ Recommended BPF Murata SFSRA4M50DF00-B0 (3*): Recommended constant value 4.7µF to 10kΩ The ceramic capacitor may be used for the electrolytic capacitor. LA72715V, 72715VA No.A0982-5/12 ...
Page 6
... FM FILTER DC : 2.9V 5 SIF INPUT DC : 2.4V 6 GND LA72715V, 72715VA Function Reference terminal of AM detection. Absorbing the DC offset of signal line by external capacity. Absorbing the DC offset of signal line by external capacity. Filter terminal for making stable DC voltage of FM detection output in SIF part. Normally, use a condenser of 4.7µF. Increase the capacity value with concerning frequency characteristics of low level ...
Page 7
... Serial data input pin. 10 Serial CLK input pin 11 TEST1 12 EXTIN_R DC : 2.4V -14.5dBV 13 EXTIN_L DC : 2.4V -14.5dBV LA72715V, 72715VA Function Rectangle wave output for JUST CLOCK. (OPEN Collector) 100kΩ Pull-up MUTE : 3.0V to High : 2. Low : High : 2. Low : EXT input Rch ...
Page 8
... IC side, this is input operation mode), and in case of ‘H’ reading mode (As this IC side, this is output operation mode). Data works with all of bit, transfer the stop condition before stop 8bit transfer, and to stop transfer, it will be canceled the transfer dates called R/W bit. LA72715V, 72715VA Function Line output pin. Detection output for M.T.S. signal. BILINGUAL :3 ...
Page 9
... Fall time of both SDA and SDL signals Data hold time Data set-up time Set-up time for STOP condition BUS free time between a STOP and START condition Definition of Timing LA72715V, 72715VA R/W ACK Control data L R/W ACK Internal Data * STEREO ...
Page 10
... SLAVE ADDRESS 80H (16pin : OPEN) SLAVE ADDRESS 84H (16pin : SLAVE ADDRESS A0H (16pin : GND) LA72715V, 72715VA Normal (MUTE OFF Mode (SW Normal) EXT Mode (SW EXT) ...
Page 11
... Slave address select 1.5V : A0H, OPEN : 80H, 3. 84H Serial Data Specification (I MSB D8 D7 SIF or TEST BASE BAND 0 : SIF 0 : OFF 0 : OFF 1 : BASE BAND Note : Underline shows default setting LA72715V, 72715VA OUTPUT MODE LCH (18pin MAIN ...
Page 12
... LA72715V/VA Reference Characteristics Output frequency characteristics TYP (30%MOD SIF_IN – 2 – 4 – 6 – 8 – 0.01 0.1 Frequency, f – kHz Main degree of modulation – Output level & Distortion factor TYP (1kHz SIF_IN) 2000 1500 1000 500 0 0 100 200 Main degree of modulation – ...