LUCL8576BP-D AGERE [Agere Systems], LUCL8576BP-D Datasheet - Page 6

• Manufacturer Part Number: LUCL8576BP-D
• Description: Dual Ringing SLIC
• Manufacturer: AGERE [Agere Systems]

L8576B Dual Ringing SLIC
Pin Information
Table 1. Pin Descriptions (continued)
* On the printed-wiring board (PWB), make the leads to BGND and V
Note: I
6
Circuit
mize the amount of PWB copper on all leads connected to this device for the lowest operating temperature.
Pin,
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
a
u
and O
Circuit
u
Pin,
10
11
12
13
14
15
16
17
18
19
20
21
22
23
indicate a pull-up device is included on this lead.
b
6
7
8
9
RNGNG
Symbol Type
NSTAT
NDISC
RPWR
RTFLT
AGND
RRNG
RCVP
RCVN
RTTH
DC
VITR
I
TG2
TG1
PROG
V
PR
PT
(continued)
CC
OUT
I/O
I/O
O
—
—
—
—
—
—
—
—
I
I
O
O
I
I
I
u
u
u
Ringing Input. Refer to Operating States section. A pull-up device is
included.
Loop Detector Output/Ring Trip Detector Output. When low, this lead indi-
cates an off-hook condition. When in ringing mode, a low output on this lead
indicates a ring trip. A pull-up device is included.
Disconnect Input. Refer to Operating States section. A pull-up device is
included.
Power Resistor. Connect a resistor between this pin and V
resistor should be used for a V
calculate resistor values for other V
Protected Tip. The input to the tip fault protection and output of tip current
drive amplifier. Connect this pin to the tip of the loop through a 30
age protection resistor.
Protected Ring. The input to the ring fault protection and output of ring cur-
rent drive amplifier. Connect this pin to the ring of the loop through a 30
overvoltage protection resistor.
Transmit ac Output Voltage. This output is a voltage that is directly propor-
tional to the differential tip/ring current.
Transmit Gain 2. Transmit gain and current limiting for ringing is set by the
value of R
Transmit Gain 1. Transmit gain is set by the series resistor combination of
R
Ring Trip Filter. Connect this lead to RTTH via a resistor and to AGND with a
capacitor to filter the ring trip circuit to prevent spurious responses.
Ring Trip Threshold. Connect this lead to DC
trip threshold.
dc Voltage Out. This output is a voltage that is directly proportional to the
absolute value of the differential tip/ring current.
Current-Limit Program Input. A resistor to DC
the circuit.
Receive Signal Input (+). This high-impedance input controls the ac differen-
tial voltage on tip/ring.
Receive Signal Input (–). This high-impedance input controls the ac differen-
tial voltage on tip/ring.
Analog Signal Ground.
Analog 5 V Power Supply.
Ringing Slope Resistor. Connect this lead to AGND with a resistor to set the
slope of the ringing waveform. Note that this pin is shared with both sections.
GX1
and R
GX2
GX2
. R
from this lead to TG2.
GX2
BAT
is connected between TG2 and VITR.
as wide as possible for thermal and electrical reasons. Also, maxi-
Name/Function
BAT
of –68.5 V. See the Applications section to
BAT
potentials.
OUT
OUT
via a resistor to set the ring
sets the dc current limit of
Agere Systems Inc.
BAT
. A 2.2 k , 2 W
May 2001
overvolt-