AR1100-I MICROCHIP [Microchip Technology], AR1100-I Datasheet - Page 31

• Manufacturer Part Number: AR1100-I
• Description: AR1100 Resistive USB and RS-232 Touch Screen Controller
• Manufacturer: MICROCHIP [Microchip Technology]

• host presents last target (9
• operator touches (and releases) sensor at last tar-
• the 5
• 0xXXXX and 0xYYYY are RAW coordinates of the
• device indicates exit from calibration mode with
0xFF indicates ‘exit’ Calibration mode, XX and YY are
don’t care
• host terminates the target display
• device returns to normal operation
7.3
The AR1100 supports a low-power, Sleep mode used
to conserve power when the device is not in use.
When in UART Communication mode, Sleep mode is
activated after a specified time interval (parameter reg-
ister: SleepDelay) during which no touch or communi-
cation took place. When in Sleep, the device can be
awakened by a touch or by any communication from
the host. The first byte of communication used to wake
up the device will be lost/ignored.
When in USB Communication mode, Sleep mode is
activated by a USB SUSPEND control transfer from the
host – the SleepDelay timer has no effect. Optionally, if
the host is configured to allow the device to awaken the
host (USB REMOTE WAKE-UP), the host will preface
the USB SUSPEND with a control transfer to enable
remote wake-up from the device. In this situation, a
touch can awaken the host; otherwise, only a RESUME
condition from the host will wake-up the AR1100.
7.4
The AR1100 must be configured for the sensor type
connected (i.e., 4W, 5W or 8W) using a combination of
the MODE input pin and configuration parameter
TouchOptions. For a 5W sensor, the mode input pin
must be grounded. For a 4W or 8W sensor, the mode
input pin should be open/disconnected. Additionally, bit
1 in Configuration register TouchOptions is used to
further select between 4W and 8W.
As seen in
is typically connected to a hardware jumper (J1).
Because this pin is equipped with an internal pull-up
resistor, it can be grounded with a jumper or simply left
disconnected (no jumper).
 2011 Microchip Technology Inc.
get <0x55> <0x07> <0x00> <0x14> <0x08>
<0xXX> <0xXX> <0xYY> <0xYY>
(the 9
touch point (16-bit, little endian)
<0x55> <0x07> <0x00> <0x14> <0xFF>
<0xXX> <0xXX> <0xYY> <0xYY>
th
th
Sleep
byte indicates the calibration point 0x08
)
Configure Sensor Type
FIGURE B-1:
“Schematic”, the MODE pin
th
in this example)
7.5
The LED provides an indication of controller status. As
summarized in
touch is detected, and a ‘slow’ blink indicates no touch.
FIGURE 7-2:
TABLE 7-1:
7.6
Low-level operations (configuration, calibration, boot
load) are supported in only 2 of the 4 communication
modes (i.e., UART and HID-GENERIC). If the AR1100
is operating in HID-MOUSE or HID-DIGITIZER mode,
it must be configured to HID-GENERIC for the low-level
operations, then reconfigured back to the desired
(default) device type.
Three 3-byte commands are provided to assign the
USB device type (refer to
1.
2.
3.
Each command sets the default USB device type (in
nonvolatile memory), then resets the AR1100 – caus-
ing it to re-enumerate. All three device types will accept
the
SET_FEATURE control transfer or a standard WRITE
data transfer (via the interrupt-end point). The HID-
MOUSE device under MS Windows
SET_FEATURE only.
LED blinks slowly
(once per second)
LED blinks rapidly (5
times per second)
LED is off
USB_MODE_GENERIC
USB_MODE_MOUSE
USB_MODE_DIGITIZER
mode
Behavior
USB Mode Change
LED
change
Table
LED INDICATOR
7-1, a ‘fast’ blink indicates that a
LED SCHEMATIC
Controller is powered, awake
and no touch is detected
Controller detects a touch
Controller has no power or is
asleep (suspended)
commands
Section 5.0,
Status
®
DS41606B-page 31
may be limited to
Commands).
as
either
a