LA1193M_08 SANYO [Sanyo Semicon Device], LA1193M_08 Datasheet
LA1193M_08
Related parts for LA1193M_08
LA1193M_08 Summary of contents
Page 1
Ordering number : EN4715B LA1193M LA1193V Overview The LA1193M and LA1193V are front-end ICs developed for use in car radios. It incorporates an extremely wide dynamic range mixer and a new AGC system consisting of a dual-system wide-band AGC and ...
Page 2
Functions • Double-balance mixer • Pin diode drive output • Differential IF amplifier • Dual-system wide-band AGC circuit • Local buffer output • 3D-AGC system • FET gate drive AGC output • IF amplifier gain control pin Specifications Maximum Ratings ...
Page 3
Package Dimensions unit : mm (typ) 3179C Block Diagram and Test Circuit Diagram SFE-10.7MS3A10-A TO FMIF INPUT LA1193-OUTPUT 330Ω VCL 20 19 KEYED BUFF OSC 1 2 1000pF OSC OSC BUFF B V OSC -BUFFER 1000pF 1kΩ 22pF ...
Page 4
Application Circuit Example : USA and Europe Application Circuit Example : Japan FM IF SFE-10.7MS3A10-A SMETER VCL KEYED BUFF OSC OSC 100pF GND OSC OSC BUFF B PLL 15pF SUMIDA 22pF SA-125 10pF SVC203 ...
Page 5
Coil Specifications Coils Manufactured by Sumida Electronics Japan band RF coil SA-129 or SA-143 Japan antenna coil SA-123 or SA-144 US band antenna coil SA-140 or SA-231 Mixer coil (for both bands) SA-266 ...
Page 6
Pin Functions Pin No. Function 1 OSC BUFF 2 OSC Tr. base 3 OSC GND 4 OSC Tr. emitter 5 OSC Mix input (1) 7 Mix input (2) 10 Mix out (1) 11 Mix out (2) 9 ...
Page 7
Continued from preceding page. Pin No. Function 8 W-AGC input 13 N-AGC input 14 IF AMP bypass 15 IF AMP input 18 IF AMP output 19 IF AMP gain adjust 16 RF AGC OUTPUT LA1193M, 1193V Equivalent circuit Since the ...
Page 8
Continued from preceding page. Pin No. Function 17 IF, AGC Keyed AGC input 1. Oscillator Circuit 2. Local Oscillator Buffer Output LA1193M, 1193V Equivalent circuit Steps were taken to prevent AMR degradation during earlier product type AGC ...
Page 9
Interference Characteristics The LA1193M incorporates a newly developed 3D-AGC (triple dimension) circuit. This circuit allows three-signal interference characteristics (inter-modulation characteristics) and two-signal sensitivity suppression characteristics to be provided at the same time, a combination of characteristics previously thought difficult ...
Page 10
Features of the Double Wide AGC System — Since this is a mixer input detection wide-band AGC, it prevents the occurrence of intermodulation due to interfering stations with ∆f > 1MHz. (TV band interference prevention) — Since this system uses ...
Page 11
Sensitivity, ∆f and V 20 Characteristics Two signal sensitivity suppression improvement Desired station AGC sensitivity — The W-AGC sensitivity is determined by the antenna RF circuit selectivity independently — The N-AGC sensitivity is determined by ...
Page 12
IF Amplifier This IF amplifier is a single stage differential amplifier. Specifications Input impedance : 330Ω Output impedance : 330Ω Gain : 25dB Gain adjustment can be provided using either of the methods shown. IF Gain adj Temperature Characteristics ...
Page 13
Wide AGC circuit The wide AGC sensitivity is set by the value of the capacitor on pin 8. However, since incorrect operation due to the local oscillator signal may occur if this capacitor is too large, its value must ...
Page 14
Three-signal interference characteristics 70 3SK251+LA1193M or 1193V+LA1145M 8. 83MHz dev = 22.5kHz 1kHz fuD1 = f r ± ∆ f non dev 40 fuD2 = f r ± 2 ∆ f ...
Page 15
Vo AGC , I ANT MIX 10 V AGC OUT 8. AGC OUT 7. 8.0V IANT 7.0V IANT ...
Page 16
V AGC -- V CL20 140 10.7MHz W-AGC-OFF Cannot be measured 130 for values higher than 126dBµ 120 7. 8.5V 7.0V 110 8.0V 100 90 80 0.4 0.6 0.8 1.0 1.2 Pin 20 voltage, ...
Page 17
V AGC OUT -- 8. 83MHz 100dBµ W-AGC OFF 8 (With pin 8 connected to ground) MIX input 0.2 0.4 0.6 0.8 1.0 Pin ...
Page 18
130 120 110 100 input voltage -- dBµ IF AMP -- f 130 8. 100dBµ (pin 15) 120 110 ...
Page 19
100 120dBµ 90dBµ 88 80dBµ 70dBµ 60dBµ -60 -40 - Ambient temperature ° 100 98 −3dB ...
Page 20
LA1193M, 1193V No.4715-20/22 ...
Page 21
LA1193M, 1193V No.4715-21/22 ...
Page 22
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all ...