PM39LV010-70JCE PMC [PMC-Sierra, Inc], PM39LV010-70JCE Datasheet - Page 6

• Manufacturer Part Number: PM39LV010-70JCE
• Description: 512 Kbit / 1Mbit / 2Mbit / 4Mbit 3.0 Volt-only CMOS Flash Memory
• Manufacturer: PMC [PMC-Sierra, Inc]

PMC
DEVICE OPERATION (CONTINUED)
CHIP ERASE
The entire memory array can be erased through a chip
erase operation. Pre-programs the devices are not
required prior to a chip erase operation. Chip erase starts
immediately after a six-bus-cycle chip erase command
sequence. All commands will be ignored once the chip
erase operation has started. The devices will return to
standby mode after the completion of chip erase.
SECTOR AND BLOCK ERASE
The memory array of Pm39LV512/010/020/040 are or-
ganized into uniform 4 Kbyte sectors. A sector erase
operation allows to erase any individual sector without
affecting the data in others. The memory array of
Pm39LV010/020/040, excluding Pm39LV512, are also
organized into uniform 64 Kbyte blocks (sector group -
consists of sixteen adjacent sectors). A block erase
operation allows to erase any individual block. The sec-
tor or block erase operation is similar to chip erase.
I/O7 DATA# POLLING
The Pm39LV512/010/020/040 provide a Data# Polling
feature to indicate the progress or completion of a pro-
gram and erase cycles. During a program cycle, an at-
tempt to read the devices will result in the complement
of the last loaded data on I/O7. Once the program op-
eration is completed, the true data of the last loaded
data is valid on all outputs. During a sector, block, or
chip erase cycle, an attempt to read the device will re-
sult a “0” on I/O7. After the erase operation is completed,
an attempt to read the device will result a “1” on I/O7.
I/O6 TOGGLE BIT
The Pm39LV512/010/020/040 also provide a Toggle Bit
feature to detect the progress or completion of a pro-
gram and erase cycles. During a program or erase cycle,
an attempt to read data from the device will result a
toggling between “1” and “0” on I/O6. When the program
or erase operation is complete, I/O6 will stop toggling
and valid data will be read. Toggle bit may be accessed
at any time during a program or erase cycle.
Programmable Microelectronics Corp.
Pm39LV512 / Pm39LV010 / Pm39LV020 / Pm39LV040
6
HARDWARE DATA PROTECTION
Hardware data protection protects the devices from un-
intentional erase or program operation. It is performed
in the following ways: (a) V
V (typical), the write operation is inhibited. (b) Write in-
hibit: holding any of the signal OE# low, CE# high, or
WE# high inhibits a write cycle. (c) Noise filter: pulses
of less than 5 ns (typical) on the WE# or CE# input will
not initiate a write operation.
P
M
D
o r
e
a
P
P
P
P
v
n
d
c i
u
m
m
m
m
u
a f
e
3
3
3
3
t c
t c
9
9
9
9
I
: D
L
L
L
L
r u
d I
V
V
V
V
Table 1. Product Identification
r e
e
5
0
0
0
n
1
1
2
4
D I
f i t
2
0
0
0
c i
t a
o i
n
Issue Date: December, 2003 Rev: 1.2
CC
sense: if V
CC
is below 1.8
D
9
3
1
1
3
a
D
D
B
C
E
a t
h
h
h
h
h