28F640W30 NUMONYX [Numonyx B.V], 28F640W30 Datasheet - Page 62
28F640W30
Manufacturer Part Number
28F640W30
Description
Numonyx Wireless Flash Memory (W30)
Manufacturer
NUMONYX [Numonyx B.V]
Datasheet
1.28F640W30.pdf
(102 pages)
- Current page: 62 of 102
- Download datasheet (2Mb)
11.3.2
Note:
11.3.3
11.3.4
Datasheet
62
Setup
After receiving the EFP Setup (30h) and EFP Confirm (D0h) command sequence, SR[7]
transitions from a 1 to a 0, indicating that the WSM is busy with EFP algorithm startup.
A delay before checking SR[7] is required to allow the WSM time to perform all of its
setups and checks (V
register bits SR[4], SR[3], and/or SR[1] are set, and the EFP operation terminates.
After the EFP Setup and Confirm command sequence, reads from the flash device
automatically output status register data. Do not issue the Read Status Register
command, because this command is interpreted as data to program at WA
Program
After setup completion, the host programming system must check SR[0] to determine
the data-stream ready status (SR[0]=0). Each subsequent write after this check is a
program-data write to the flash memory array. Each cell within the memory word to be
programmed to 0 receives one WSM pulse; additional pulses, if required, occur in the
verify phase.
The host programmer must poll the flash device status register for the program done
state after each data-stream write.
Although the host can check full status for errors at any time, this check is necessary
only on a block basis, after EFP exit.
Addresses must remain within the target block. Supplying an address outside of the
target block immediately terminates the program phase; the WSM then enters the EFP
verify phase.
The address can either remain constant or increment. The flash device compares the
incoming address to the address stored from the setup phase (WA
The program phase concludes when the host programming system writes to a different
block address. The data supplied must be FFFFh. Upon program phase completion, the
flash device enters the EFP verify phase.
Verify
A high percentage of the flash memory bits program on the first WSM pulse. However,
EFP internal verification identifies cells that do not completely program on their first
attempt, and applies additional pulses as required.
The verify phase is identical in flow to the program phase, except that instead of
programming incoming data, the WSM compares the verify-stream data to the data
that was previously programmed into the block.
• If the addresses match, the WSM programs the new data word at the next
• If the addresses differ, the WSM jumps to the new address location.
• If the data compares correctly, the host programmer proceeds to the next word.
• If the data does not match, the host waits while the WSM applies one or more
SR[0]=1 indicates that the WSM is busy applying the program pulse.
SR[0]=0 indicates that the appropriate cell(s) within the accessed memory location
have received their single WSM program pulse, and that the flash device is ready
for the next word.
sequential memory location.
additional pulses.
PP
level and block lock status). If an error is detected, status
Numonyx™ Wireless Flash Memory (W30)
Numonyx™ Wireless Flash Memory (W30)
Order Number: 290702-13
0
).
0
November 2007
.
Related parts for 28F640W30
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Numonyx Wireless Flash Memory (W18)
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
Numonyx StrataFlash Wireless Memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
8 Mbit, low voltage, Page-Erasable Serial Flash memory with byte alterability and a 50 MHz SPI bus interface
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
128 Mbit (8 Mb 16, multiple bank, multilevel interface, burst) 1.8 V supply, secure Flash memories
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
64-Mbit, dual I/O, 4-Kbyte subsector erase, serial flash memory with 75 MHz SPI bus interface
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
512 Kbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
16 Mbit, serial Flash memory, 75 MHz SPI bus interface
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
Wireless Flash Memory (W18/W30 SCSP)
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
StrataFlash Cellular Memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V supply Flash memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
128 Mbit (8 Mb x 16, multiple bank, page, dual boot) 3 V supply Flash memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
32 Mbit (4Mb x8 or 2Mb x16, Dual Bank 8:24, Boot Block) 3V Supply Flash Memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
32 Mbit (4Mb x8 or 2Mb x16, Dual Bank 16:16, Boot Block) 3V Supply Flash Memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
64 Mbit (8Mb x8 or 4Mb x16, Multiple Bank, Page, Boot Block) 3V Supply Flash Memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet: