EMK316ABJ226ML-T ENPIRION [Enpirion, Inc.], EMK316ABJ226ML-T Datasheet - Page 11

• Manufacturer Part Number: EMK316ABJ226ML-T
• Description: 204A Voltage Mode Synchronous Buck PWM
• Manufacturer: ENPIRION [Enpirion, Inc.]

Power Up Sequence
The EN2340QI is designed to be powered by either
a single input supply (PVIN) or two separate
supplies: one for PVIN and the other for AVIN.
Single Input Supply Application (PVIN):
The EN2340QI has an internal linear regulator that
converts PVIN to 3.0V. The output of the linear
regulator is provided on the AVINO pin. AVINO
should be connected to AVIN on the EN2340QI. In
this application, the following external components
are required: Place a 1µF, X5R/X7R, capacitor
between AVINO and AGND as close as possible to
AVINO.
between AVIN and AGND as close as possible to
AVIN. In addition, place a resistor (R
VDDB and AVIN, as shown in Figure 1. Enpirion
recommends R
ENABLE cannot be asserted before PVIN. If no
external enable signal is used, tying ENABLE to
AVIN meets this requirement.
Dual Input Supply Application (PVIN and AVIN):
In this application, place a 0.1µF, X7R, capacitor
between AVIN and AGND as close as possible to
AVIN. Refer to Figure 5 for a recommended
schematic for a dual input supply application.
For dual input supply applications, the sequencing
of the two input supplies, PVIN and AVIN, is very
important. During power up, neither ENABLE nor
PVIN should be asserted before AVIN. There are
two common acceptable turn-on/off sequences for
the device. ENABLE can be tied to AVIN and come
up with it, and PVIN can be ramped up and down
as needed. Alternatively, PVIN can be brought high
after AVIN is asserted, and the device can be
turned on and off by toggling the ENABLE pin.
Enable Operation
The ENABLE pin provides a means to enable
normal operation or to shut down the device. A
logic high will enable the converter into normal
operation. When the ENABLE pin is asserted (high)
the device will undergo a normal soft-start. A logic
low will disable the converter. A logic low will power
down the device in a controlled manner and the
device is subsequently shut down. The ENABLE
signal has to be low for at least the ENABLE
Lockout Time (8ms) in order for the device to be re-
enabled.
Pre-Bias Operation
The EN2340QI is not designed to be turned on into
a pre-biased output voltage.
©Enpirion 2012 all rights reserved, E&OE
06878
Place a 0.1µF, X5R/X7R, capacitor
VB
=4.75kΩ. In this application,
VB
) between
Enpirion Confidential
April 16, 2012
Frequency Synchronization
The switching frequency of the EN2340QI can be
phase-locked to an external clock source to move
unwanted beat frequencies out of band. The
internal switching clock of the EN2340QI can be
phase locked to a clock signal applied to the S_IN
pin. An activity detector recognizes the presence of
an external clock signal and automatically phase-
locks the internal oscillator to this external clock.
Phase-lock will occur as long as the input clock
frequency is in the range of 0.9MHz to 1.3MHz.
When no clock is present, the device reverts to the
free running frequency of the internal oscillator.
Adding a resistor (R
the frequency lower. If a 3KΩ resistor is placed on
FADJ the nominal switching frequency of the
EN2340QI is 1MHz. The efficiency performance of
the
combinations can be optimized by adjusting the
switching frequency. Table 1 shows recommended
R
order to optimize performance of the EN2340QI.
FS
values for various PVIN/VOUT combinations in
PVIN
12V
EN2340QI
5V
Figure 5: Dual Input Supply (PVIN and AVIN)
Table 1: Recommended R
Recommended Schematic
FS
for
VOUT
) to the FADJ pin will adjust
5.0V
3.3V
2.5V
1.2V
1.0V
2.5V
1.2V
1.0V
www.enpirion.com, Page 11
various
FS
Values
EN2340QI
PVIN/VOUT
1.65K
22.1K
4.87K
3.01K
1.3K
15K
15K
10K
R
FS
Rev: B