ACPM-7821-TR1 AVAGO [AVAGO TECHNOLOGIES LIMITED], ACPM-7821-TR1 Datasheet
ACPM-7821-TR1
Available stocks
Related parts for ACPM-7821-TR1
ACPM-7821-TR1 Summary of contents
Page 1
... Input DA Match RF Input MMIC (4) Vcc1(5) Ordering Information Part Number No. of Devices ACPM-7821-TR1 1000 ACPM-7821-BLK 100 Features • Excellent linearity • High efficiency • 10-pin surface mounting package ( 1.1 mm) • Low quiescent current • Internal 50Ω matching networks for both RF input and output • ...
Page 2
Table 1. Absolute Maximum Ratings Parameter Symbol RF Input Power Supply Voltage Reference Voltage V ref Control Voltage V cont Storage Temperature T stg Table 2. Recommended Operating Conditions Parameter Symbol DC Supply ...
Page 3
Table 4. Electrical Characteristics for CDMA Mode (Vcc=3.4V, Vref=2.85V, T=25°C) Characteristics Gain Power Added Efficiency Total Supply Current Quiescent Current Reference Current [1] Control Current Total Current in Power-down mode 0.885 MHz offset ACPR1_hi ACPR in High power mode 1.98 ...
Page 4
Characterization Data(Vcc=3.4V, Vref=2.85V, T=25°C) 500 450 400 350 300 250 200 150 100 Pout (dBm) Figure 1. Total Current vs. Output Power ...
Page 5
... C2 R1 100pF 6.2kohm Vcc1 2.2µF 22pF 68pF Figure 6. Evaluation Board Schematic AVAGO ACPM-7821 PYYWW AAAAA Figure 7. Evaluation Board Assembly Diagram Vref GND 10 2 Vcont GND 9 3 GND RF Out GND 7 5 Vcc1 Vcc2 ...
Page 6
Package Dimensions and Pin Descriptions Pin 1 Mark ± 0.1 TOP VIEW 1.9 1.0 0.5 0.85 0.6 0.85 1.7 1.9 BOTTOM VIEW Figure 8. Package Dimensional Drawing and Pin Descriptions ...
Page 7
... Package Dimensions and Pin Descriptions, Pin 1 Mark AVAGO ACPM-7821 PYYWW AAAAA Figure 9. Marking Specifications. 7 continued Manufacturing Part Number Lot Number P Manufacturing info YY Manufacturing Year WW Work Week AAAAA Assembly Lot Number ...
Page 8
... Use 50Ω transmission line between PAM and Duplexer and make it as short as possible to reduce conduction loss - π-type circuit topology is good to use for matching circuit between PA and Duplexer. - Pull-up resistor(R1) should be used to limit current drain. 6.2kΩ is recommended for ACPM-7821 Figure 10. Peripheral Circuit. ...
Page 9
... Probability Distribution Function implies that what is important for longer talk time is the efficiency of low or medium power range rather than the efficiency at full power. ACPM-7821 idle current and operating current at 17 dBm nominal condition. This PA with low current consumption pro- longs talk time by no less than 30 minutes compared to other PAs ...
Page 10
... PCB Design Guidelines The recommended ACPM-7821 PCB Land pattern is shown in Figure 14 and Figure 15. The substrate is coated with solder mask between the I/O and con- ductive paddle to protect the gold pads from short circuit that is caused by solder bleeding/bridging. Stencil Design Guidelines A properly designed solder screen or stencil is required to ensure optimum amount of solder paste is deposited onto the PCB pads ...
Page 11
Tape Drawing Dimension List Annote Millimeter A0 4.40±0.10 B0 4.40±0.10 K0 1.70±0.10 D0 1.55±0.05 D1 1.60±0.10 P0 4.00±0.10 P1 8.00±0.10 Figure 17. Tape and Reel Format – 4mm. 11 Annote Millimeter P2 2.00±0.05 P10 40.00±0.20 E 1.75±0.10 ...
Page 12
Reel Drawing BACK VIEW FRONT VIEW Figure 18. Plastic Reel Format –13"/4". 12 ...
Page 13
... After this time period, the part would need to be removed from the reel, de-taped and then re-bake. MSL classification ref low temperature for the ACPM-7821 is targeted at 250° C +0/-5° C. Figure 19 and Table 7 show typical SMT profile for maximum temperature of 250° C +0/-5° ...
Page 14
Handling and Storage, continued Figure 19. Typical SMT Reflow Profile for Maximum Temperature = 250 +0/-5°C. Table 7. Typical SMT Reflow Profile for Maximum Temperature = 250+0/-5°C Profile Feature Average ramp-up rate ( Preheat - ...
Page 15
Handling and Storage, continued Storage Conditions Packages described in this document must be stored in sealed moisture barrier, anti-static bags. Shelf life in a sealed moisture barrier bag is 12 months at <40° C and 90% relative humidity (RH) J-STD-033 ...
Page 16
Table 8. Recommended Equivalent Total Floor Life (days) @ 20°C, 25°C & 30°C For ICs with Novolac, Biphenyl and Multifunctional Epoxies (Reflow at same temperature at which the component was classified) For product information and a complete list of distributors, ...