ADS-935 MURATA-PS [Murata Power Solutions Inc.], ADS-935 Datasheet - Page 3

• Manufacturer Part Number: ADS-935
• Description: 16-Bit, 5MHz Sampling A/D Converters
• Manufacturer: MURATA-PS [Murata Power Solutions Inc.]

TECHNICAL NOTES
1. Obtaining fully specified performance from the ADS-935
2. The ADS-935 achieves its specified accuracies without the
www.cd4power.com
Internal Reference
External Current
DIGITAL OUTPUTS
Logic Levels
Output Coding
POWER REQUIREMENTS
Power Supply Ranges
Power Supply Currents
Power Dissipation
Power Supply Rejection
DYNAMIC PERFORMANCE (Cont.)
ANALOG OUTPUT
Footnotes:
requires careful attention to pc-card layout and power supply
decoupling. The device's analog and digital ground systems
are connected to each other internally. For optimal perfor-
mance, tie all ground pins (4, 7, 30 and 36) directly to a large
analog ground plane beneath the package.
For the best performance it is recommended to use a single
power source for both the +5V analog and +5V digital supplies.
Bypass all power supplies and the +3.2V reference output to
ground with 4.7μF tantalum capacitors in parallel with 0.1μF
ceramic capacitors. Locate the bypass capacitors as close to
the unit as possible.
need for external calibration. If required, the device's small
initial offset and gain errors can be reduced to zero using
the adjustment circuitry shown in Figure 2. When using this
circuitry, or any similar offset and gain calibration hardware,
make adjustments following warm-up. To avoid interaction,
always adjust offset before gain. Tie pins 5 and 6 to ANALOG
GROUND (pin 4) if not using offset and gain adjust circuits.
Voltage
Drift
Logic "1"
Logic "0"
Logic Loading "1"
Logic Loading "0"
+5V Supply
–5V Supply
+12V Supply
–12V Supply
+15V Supply
–15V Supply
+5V Supply
–5V Supply
–12/15V Supply
+12/15V Supply
Effective bits is equal to:
All power supplies must be on before applying a start convert pulse. All
supplies and the clock (START CONVERT) must be present during warm-up
periods. The device must be continuously converting during this time.
When COMP . BITS (pin 35) is low, logic loading "0" will be –350μA.
A 5MHz clock with a 50nsec positive pulse width is used for all production
testing. See Timing Diagram for more details.
(SNR + Distortion) – 1.76 +
6.02
20 log
+4.75
–4.75
+11.5
–11.5
+14.5
–14.5
MIN.
+2.4
—
—
—
—
—
—
—
—
—
—
—
—
(Offset) Binary / Complementary (Offset) Binary / Two's Complement / Complementary Two's Complement
Actual Input Amplitude
Full Scale Amplitude
+25°C
+12.0
–12.0
+15.0
–15.0
TYP .
+200
–100
+3.2
+5.0
–5.0
2.85
±30
+85
–65
—
—
—
—
—
5
MAX.
+5.25
–5.25
+12.5
–12.5
+15.5
–15.5
±0.07
+0.4
3.1
–4
+4
—
—
—
—
—
—
—
—
+4.75
–4.75
+11.5
–11.5
+14.5
–14.5
+2.4
MIN.
—
—
—
—
—
—
—
—
—
—
—
—
3. Pin 35 (COMP . BITS) is used to select the digital output
4. To enable the three-state outputs, connect OUTPUT
This is the time required before the A/D output data is valid once the analog
input is back within the specified range.
See table 2a, Setting Output Coding Selection.
The minimum supply voltages of +4.9V and –4.9V for ±V
–55°C operation only. The minimum limits are +4.75V and –4.75V when
operating at +125°C.
±12V only or ±15V only required.
coding format of the ADS-935. See Tables 2a and 2b.
When this pin has a TTL logic "0" applied, it complements all
of the ADS-935’s digital outputs.
When pin 35 has a logic "1" applied, the output coding is
complementary (offset) binary. Applying a logic "0" to pin 35
changes the coding to (offset) binary. Using the MSB output
(pin 29) instead of the MSB output (pin 28) changes the
respective output codings to complementary two's
complement and two's complement.
Pin 35 is TTL compatible and can be directly driven with
digital logic in applications requiring dynamic control over
its function. There is an internal pull-up resistor on pin 35
allowing it to be either connected to +5V or left open when a
logic "1" is required.
ENABLE (pin 34) to a logic "0" (low). To disable, connect pin
34 to a logic "1" (high).
0 TO +70°C
+12.0
+15.0
–12.0
–15.0
+220
–150
+3.2
+5.0
TYP .
–5.0
2.85
±30
–65
+85
—
—
—
—
—
5
MAX.
+5.25
–5.25
+12.5
–12.5
+15.5
–15.5
±0.07
+0.4
3.5
–4
+4
—
—
—
—
—
—
—
—
+11.5
+14.5
–11.5
–14.5
+2.4
+4.9
–4.9
MIN.
—
—
—
—
—
—
—
—
—
—
—
—
–55 TO +125°C
+12.0
+15.0
–12.0
–15.0
+220
–150
+3.2
+5.0
–5.0
2.85
TYP .
±30
—
—
—
—
—
—
—
5
DD
+5.25
–5.25
+12.5
–12.5
+15.5
–15.5
±0.07
are required for
+0.4
MAX.
3.5
—
—
—
—
–4
+4
—
—
—
—
Page 3 of 8
%FSR/%V
ppm/°C
UNITS
Watts
Volts
Volts
Volts
Volts
Volts
Volts
Volts
Volts
Volts
mA
mA
mA
mA
mA
mA
mA