F721A107MR NICHICON [Nichicon corporation], F721A107MR Datasheet

F721A107MR

Manufacturer Part Number

F721A107MR

Description

SOLID TANTALUM ELECTROLYTIC CAPACITORS

Manufacturer

NICHICON [Nichicon corporation]

Datasheet

1.F721A107MR.pdf (1 pages)

Current page: 1 of 1
Download datasheet (86Kb)

SOLID TANTALUM ELECTROLYTIC CAPACITORS

F72

F75

Case code

F72

Adapted to the RoHS directive (2002/95/EC).

Drawing

Dimensions

Drawing

Dimensions

Standard ratings

Type numbering system (Example : 10V 100µF)

Type numbering system (Example : 16V 150 F)

Cap.(µF)

7.3 ± 0.3 4.3 ± 0.3 2.8 ± 0.3 1.3 ± 0.4 3.9 ± 0.6

7.1 ± 0.3 3.2 ± 0.3 2.5 ± 0.3 1.3 ± 0.3 3.6 ± 0.6

7.2 ± 0.3 6.0 ± 0.3 3.5 ± 0.3 1.3 ± 0.4 3.8 ± 0.6

033

047

068

100

150

220

330

Case code

Code

336

476

686

107

157

227

337

7.2

Low Profile

Conformal

coated Chip

0.3 6.0

0.3 1.2

D dimension only for reference

0.3 1.3

6.3

Solder electrode

0.4 3.8

(R)

0.6

(6.0)

(6.4)

(6.2)

(D)

(6.2)

(D)

(mm)

F75

Dissipation Factor

Category

Temperature Range

Leakage Current

Capacitance Change

by Temperature

Damp Heat

Temperature Cycles

Resistance to

Soldering Heat

Surge

Endurance

Shear Test

Terminal Strength

Capacitance Tolerance

As for the surge and derated voltage at 125

Specifications

(100kHz)

(120Hz)

Item

ESR

Maximum CV

Conformal

coated Chip

Cap. (µF)

1000

1500

2200

068

100

150

220

330

470

680

--55 ~ + 125 ˚C (Rated temperature : + 85 ˚C )

± 20%, ± 10% (at 120Hz)

33~68µF

100µF~

150µF

220µF~330µF

100µF~

+15% Max. (at +125 ˚C )

+10% Max. (at +85 ˚C )

--10% Max. (at --55 ˚C )

After applying the pressure load of 5N

center of capacitor side body which has

no electrode and has been soldered

beforehand on an aluminum substrate,

there shall be found neither exfoliation

nor its sign at the terminal electrode.

Keeping a capacitor surface-mounted on a substrate upside

down and supporting the substrate at both of the opposite

bottom points 45mm apart from the center of the capacitor,

the pressure strength is applied with

a specified jig at the center of the

substrate so that the substrate may

bend by 1mm as illustrated. Then,

there shall be found no remarkable

abnormality on the capacitor terminals.

At -- 55 ˚C / +125 ˚C , 30 minutes each, For 5 cycles,

Reflow at 260 ˚C for 10 seconds , Dipping Flow at 260 ˚C for 10 seconds

After application of surge in series with a 33 resistor at the rate of 30

seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85 ˚C ,

capacitors meet the characteristics requirements listed below.

After 2000 hours' application of rated voltage at 85 ˚C , or derated voltage at

125 ˚C , capacitors meet the characteristic requirements listed below.

for 10±1 seconds horizontally to the

At 40 ˚C , 90~95% R.H., For 500 hours (No voltage applied)

•

33µF

47µF

68µF

Code

After 1 minute's application of rated voltage, leakage current at 20˚C is not

After 1 minute's application of rated voltage, leakage current at 85˚C is not

After 1 minute's application of derated voltage, leakage current at 125˚C is

Capacitance Change

Dissipation Factor

Leakage Current

more than 0.01CV or 0.5µA, whichever is greater.

more than 0.1CV or 5µA, whichever is greater.

not more than 0.125CV or 6.3µA, whichever is greater.

Leakage Currentv

Capacitance Change

Dissipation Factor

Capacitance Change

Dissipation Factor

Leakage Current

Capacitance Change

Dissipation Factor

Leakage Current

Capacitance Change

Dissipation Factor

Leakage Current

686

107

157

227

337

477

687

108

158

228

0.90

0.80

0.75

0.70

F72

•

• • • • • • • • • • •

6%Max.

8%Max.

10%Max.

12%Max.

• • • • • • • • • • • •

• • • • • • • • • •

Per formance Characteristics

˚C

• • • • • •

, refer to page 266 for details.

• • • • • •

6.3

Within ±10% of initial value