RN41SM-I/RM Roving Networks, RN41SM-I/RM Datasheet
![no-image](/images/no-image-200.jpg)
RN41SM-I/RM
Specifications of RN41SM-I/RM
Available stocks
Related parts for RN41SM-I/RM
RN41SM-I/RM Summary of contents
Page 1
... Asset tracking • Description The RN-41 module is a small form factor, low power, class 1 Bluetooth radio that is ideal for designers who want to add wireless capability to their products without spending significant time and money developing Bluetooth-specific hardware and software. The RN-41 supports multiple interface protocols, is simple to design in, and is fully certified, making it a complete embedded Bluetooth solution ...
Page 2
OVERVIEW • Baud rate speeds: 1,200 bps up to 921 Kbps, non-standard baud rates can be programmed Class 1 radio, 330’ (100 m) range, 15 dBm output transmitter, -80 dBm typical receive sensitivity • • Frequency 2,402 ~ 2,480 MHz ...
Page 3
... Min. Typ. Max. -0.4 - +0.8 0.7 VDD - VDD + 0 0.2 VDD - 0.2 - +0.2 +1.0 +5.0 Version 3.3r 4/9/2012 RN -41 -DS Bluetooth Units Specification ≤ -70 dBm dBm dBm ≤ 20 dBm dBm dBm 75 kHz kHz kHz ≤ 1000 kHz - 40 kHz - 20 kHz > 140 kHz kHz kHz - ...
Page 4
... Table 6. Pin Description Pin Name 1 GND Ground 2 SPI_MOSI Programming only 3 GPIO6 Set Bluetooth master (high = auto-master mode) 4 GPIO7 Set baud rate (high = force 9,600, low = 115 K or firmware setting) 5 RESET Active-low reset 6 SPI_CLK Programming only 7 PCM_CLK PCM interface ...
Page 5
Pin Name 17 USB_D+ USB port 18 USB_D- USB port 19 GPIO2 Status, high when connected, low otherwise 20 GPIO3 Auto discovery = high 21 GPIO5 Status, toggles based on state, low on connect 22 GPIO4 Set factory defaults 23 ...
Page 6
TYPICAL APPLICATION SCHEMATIC Figure 4 shows a typical application schematic. Figure 4. Application Schematic www.rovingnetworks.com Version 3.3r 4/9/2012 RN -41 -DS 6 ...
Page 7
... MCP809, MCP102/121, and Torex XC61F. Factory Reset Using GPIO4 Roving Networks recommends that designers connect the GPIO4 pin to a switch, jumper, or resistor so it can be accessed. This pin can be used to reset the module to its factory default settings, which is critical in situations where the module has been misconfigured ...
Page 8
... Using the module in HCI mode allows designers to implement profiles that are not natively supported on the Bluetooth module. NOTE: HCI mode requires a separate firmware build that must be loaded into the module’s flash at the factory. Is not upgradeable in the field. Roving Networks offers HCI mode in two hardware interfaces: • HCI over UART HCI over USB • ...
Page 9
... Because the RN-41-N does not contain an antenna, it does not carry regulatory approvals. If designers use Roving Networks recommended design, they can file for a permissible antenna change and use Roving Networks’ regulatory approvals. Roving Networks recommends the Yageo chip antenna for the RN-41-N module. For detailed information on this antenna, refer to the Yageo chip antenna data sheet on the Support page of the Roving Networks website at http://www ...
Page 10
... USB firmware (HCI over USB port, slave device at 12-Mbps rate) without antenna. RN-41-N-HID HID firmware supporting HID device and SPP profiles without antenna. For other configurations, contact Roving Networks directly http://www.rovingnetworks.com for current pricing and a list of distributors carrying Roving Networks products. www.rovingnetworks.com ...
Page 11
NOTES www.rovingnetworks.com Version 3.3r 4/9/2012 RN -41 -DS 11 ...
Page 12
... Roving Networks products are not authorized for use in safety-critical applications (such as life support) where a failure of the Roving Networks product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. ...