851010AYLF IDT, 851010AYLF Datasheet
851010AYLF
Specifications of 851010AYLF
Related parts for 851010AYLF
851010AYLF Summary of contents
Page 1
Differential HCSL Fanout Buffer General Description The ICS851010 is a 1-to-10 Differential HCSL Fanout Buffer. The ICS851010 is designed to translate any differential signal levels to differential HCSL output levels. An external reference resistor is used to set the ...
Page 2
ICS851010 Data Sheet Table 1. Pin Descriptions Number Name Type 1, 2 Q0, nQ0 Output 3, 8, 13, 14, V Power DD 17, 22 Q1, nQ1 Output 6, 7 Q2, nQ2 Output 9, 25 GND Power 10 ...
Page 3
ICS851010 Data Sheet Absolute Maximum Ratings NOTE: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only. Functional operation of product at these conditions or any conditions beyond those ...
Page 4
ICS851010 Data Sheet AC Electrical Characteristics Table 3. HCSL AC Characteristics, V Symbol Parameter f Output Frequency MAX t Propagation Delay, NOTE 1 PD tsk(o) Output Skew; NOTE 2, 3 tsk(pp) Part-to-Part Skew; NOTE 3, 4 tjit Buffer Additive Phase ...
Page 5
ICS851010 Data Sheet Parameter Measurement Information V DD 33Ω 49.9Ω HCSL 33Ω GND 49.9Ω HCSL Output Load AC Test Circuit V DD nCLK V Cross Points PP CLK GND Differential Input Levels Par t 1 nQx Qx Par ...
Page 6
ICS851010 Data Sheet Parameter Measurement Information, continued Clock Period (Differential) Positive Duty Cycle (Differential) 0. Differential Measurement Points for Duty Cycle/Period nQ ∆V CROSS Q Single-ended Measurement Points for Delta Cross Point ICS851010AY REVISION A AUGUST 2, ...
Page 7
ICS851010 Data Sheet Applications Information Recommendations for Unused Output Pins Outputs: Differential Outputs All unused differential outputs can be left floating. We recommend that there is no trace attached. Both sides of the differential output pair should either be left ...
Page 8
... ICS851010AY REVISION A AUGUST 2, 2010 with the vendor of the driver component to confirm the driver and termination requirements. For example in Figure 3A, the input PP termination applies for IDT open emitter LVHSTL drivers. If you are using an LVHSTL driver from another vendor, use their termination recommendation. 3.3V CLK ...
Page 9
ICS851010 Data Sheet Recommended Termination Figure 4A is the recommended termination for applications which require the receiver and driver separate PCB. All traces should be 50Ω impedance. Figure 4A. Recommended Termination Figure 4B is the recommended ...
Page 10
ICS851010 Data Sheet Power Considerations This section provides information on power dissipation and junction temperature for the ICS851010. Equations and example calculations are also provided. 1. Power Dissipation. The total power dissipation for the ICS851010 is the sum of the ...
Page 11
ICS851010 Data Sheet The purpose of this section is to calculate power dissipation on the IC per HCSL output pair. HCSL output driver circuit and termination are shown in Figure OUT = 17mA R REF = ...
Page 12
ICS851010 Data Sheet Reliability Information θ Table 5. vs. Air Flow Table for a 32 Lead LQFP JA Meters per Second Multi-Layer PCB, JEDEC Standard Test Boards Transistor Count The transistor count for ICS851010 is: 843 ICS851010AY REVISION A AUGUST ...
Page 13
ICS851010 Data Sheet Package Outline and Package Dimensions Package Outline - Y Suffix for 32 Lead LQFP Table 6. Package Dimensions for 32 Lead LQFP JEDEC Variation: BBA All Dimensions in Millimeters Symbol Minimum Nominal 0.05 ...
Page 14
... ICS851010AY 851010AYLF ICS851010AYL 851010AYLFT ICS851010AYL NOTE: Parts that are ordered with an “LF” suffix to the part number are the Pb-Free configuration and are RoHS compliant While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use ...
Page 15
ICS851010 Data Sheet Revision History Sheet Rev Table Page Description of Change T1 2 Pin Description Table, IREF description corrected 475ohm resistor to 950ohm. 2 Corrected Output Driver Current and diagram Added note, “Characterized using....”. 5 Added Propagation ...
Page 16
... IDT or any third parties. IDT’s products are not intended for use in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT ...