MAX5389EVKIT+ Maxim Integrated, MAX5389EVKIT+ Datasheet - Page 4

no-image

MAX5389EVKIT+

Manufacturer Part Number
MAX5389EVKIT+
Description
Digital Potentiometer ICs MAX5389 Eval Kit
Manufacturer
Maxim Integrated
Datasheet

Specifications of MAX5389EVKIT+

Rohs
yes
Resistance
200 Ohms
Temperature Coefficient
35 PPM / C
Tolerance
25 %
Number Of Pots
Dual
Taps Per Pot
256
Wiper Memory
Volatile
Digital Interface
Up/Down
Description/function
Dual Up/Down Interface Digital Potentiometer
Operating Supply Voltage
2.6 V to 5.5 V
Supply Current
1 uA
Supply Voltage - Max
5.5 V
Supply Voltage - Min
2.6 V
MAX5389 Evaluation Kit
To increment wiper WA position:
1) Press SW1 and hold (CSA = low), or remove the shunt
2) Press, then release SW3 (INCA high-to-low transition).
To decrement wiper WA position:
1) Press SW1 and hold (CSA = low), or remove the shunt
2) Press SW2 and hold (UDA = low).
3) Press, then release SW3 (INCA high-to-low transition)
Jumpers JU5, JU6, and JU7 configure the EV kit opera-
tion for pushbutton control of the MAX5389 CSB, UDB,
and INCB digital inputs, respectively. Install shunts
across jumpers JU5, JU6, and JU7 for wiper WB posi-
tioning using pushbutton switches SW4, SW5, and SW6.
SW4 sets chip-select input CSB low. SW5 configures
the wiper for incrementing or decrementing operation
(UDB). SW6 controls the wiper position. The MAX5389
increments or decrements the wiper WB position on a
high-to-low transition at INCB.
Remove the shunts at JU5, JU6, and JU7 to position WB
using digital signals at header J1 (pins J1-9, J1-11, and
J1-13). See Table 1 for proper JU5, JU6, and JU7 jumper
configurations.
To increment wiper WB position:
1) Press SW4 and hold (CSB = low), or remove the shunt
Table 4. JU8 and JU9 Jumper Functions (Potentiometer A)
*Default position.
Table 5. JU10 and JU11 Jumper Functions (Potentiometer B)
*Default position.
4
Not installed*
Not installed*
at jumper JU2.
at jumper JU2.
at jumper JU5.
______________________________________________________________________________________
Installed
Installed
JU10
JU8
SHUNT POSITION
SHUNT POSITION
Not installed
Not installed
Not installed
Not installed
Installed*
Installed*
Installed
Installed
JU11
JU9
Potentiometer B Control
Connected to VDD
Connected to VDD
Not connected
Not connected
HA PAD
HB PAD
Connected to GND
Connected to GND
Connected to GND
Connected to GND
Not connected
Not connected
Not connected
Not connected
2) Press, then release SW6 (INCB high-to-low transition).
To decrement wiper WB position:
1) Press SW4 and hold (CSB = low), or remove the shunt
2) Press SW5 and hold (UDA = low).
3) Press, then release SW6 (INCB high-to-low transition).
The EV kit provides an option to configure the MAX5389
as a potentiometer or a voltage-divider open-ended or
with ground reference, respectively. Use jumpers JU8
and JU9 for potentiometer A and jumpers JU10 and
JU11 for potentiometer B configuration. Tables 4 and 5
list the jumper options for configuring potentiometers A
and B.
The MAX5389 can also be configured as a variable
resistor by shorting the H_ and W_ pads using a wire.
When operating as a variable resistor, any power source
connected to the H_, W_, or L_ pad must be voltage and
current limited to the maximum conditions stated in the
MAX5389 IC data sheet.
Note that to test the device in resistor mode, the
ohmmeter must be GND referenced to the MAX5389.
This can be accomplished by connecting the L_ pad to
GND or the H_ pad to VDD. Resistance is then measured
between the W_ and L_ or W_ and H_ PCB pads.
LA PAD
LB PAD
Potentiometer, Voltage-Divider or Variable Resistor,
at jumper JU5.
Potentiometer open-ended
Potentiometer with GND reference
Voltage-divider open-ended
Voltage-divider with GND reference
Potentiometer open-ended
Potentiometer with GND reference
Voltage-divider open-ended
Voltage-divider with GND reference
MAX5389 FUNCTION
MAX5389 FUNCTION
with Ground Reference

Related parts for MAX5389EVKIT+