MAX4198ESA-T Maxim Integrated, MAX4198ESA-T Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
MAX4198ESA-T
Manufacturer Part Number
MAX4198ESA-T
Description
Differential Amplifiers
Manufacturer
Maxim Integrated
Series
MAX4198, MAX4199r
Datasheet
1.MAX4198ESA.pdf
(12 pages)
Specifications of MAX4198ESA-T
Number Of Channels
1 Channel
Available Set Gain
0 dB
Input Offset Voltage
0.5 mV
Common Mode Rejection Ratio (min)
74 dB
Operating Supply Voltage
3 V, 5 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Maximum Dual Supply Voltage
+/- 3.75 V
Maximum Input Resistance
0.05 MOhms
Maximum Power Dissipation
471 mW
The MAX4198/MAX4199 output stage incorporates a
common-source rail-to-rail structure which maximizes the
dynamic range of the differential amplifier. The output
can swing to within 100mV from each rail with a 5kΩ load
to V
The MAX4198/MAX4199 have an active-low shutdown
input. SHDN input logic thresholds are referenced to
V
rail places the amplifiers in a 12µA (max) shutdown
mode. The MAX4198/MAX4199 exit or enter shutdown
in 35µs. In shutdown, the OUT pin is high-impedance.
The MAX4198/MAX4199 are relatively immune to oscilla-
tions caused when driving large capacitive loads.
Although heavy load capacitance increases transient ring-
ing, sustained oscillations typically do not occur for loads
under 600pF (see Pulse Response with Capacitive Load
in the Typical Operating Characteristics). Applications that
require driving higher capacitive loads can isolate the out-
put capacitance using a 15Ω to 100Ω resistor between the
amplifier output and the load (Figure 1). Although adding
an isolation resistor dampens the response enough to pre-
vent oscillations, it does so at the expense of bandwidth
and DC accuracy.
The MAX4198/MAX4199 operate from single +2.7V to
+7.5V supplies or from dual ±1.35V to ±3.75V supplies,
and they consume only 45µA of supply current.
Excellent power-supply rejection permits the amplifiers
to be operated directly from a decaying 3V cell without
excessive error. To maximize AC performance, the sup-
ply must be bypassed with a 0.1µF ceramic capacitor
to ground that must be as close as possible to the pin.
If dual supplies are used, bypass both supply pins with
0.1µF to ground.
Differential amplifiers can be used in single-ended and
other amplifier applications. Figures 2 through 6 show
the MAX4198/MAX4199 in different configurations. The
internally trimmed and matched resistors offer conven-
ience and have a distinct advantage over external
resistors. These amplifiers are not compensated for sin-
gle-ended unity gain; therefore, IN- should not be con-
nected to OUT or left unconnected.
Micropower, Single-Supply, Rail-to-Rail
Precision Differential Amplifiers
10
CC
CC
, not to GND. Pulling SHDN 2.5V below the positive
______________________________________________________________________________________
/ 2 (see the Typical Operating Characteristics).
Applications Information
Power Supply Considerations
Driving Capacitive Loads
Rail-to-Rail Output Stage
Application Circuits
Shutdown Mode
Figure 1. Dual-Supply, Capacitive-Load Driving Circuit
Figure 2. Standard Difference Amplifier
Figure 3. Precision Inverting Buffer
INPUT
V
V
A
B
V
IN+
IN-
IN+
A
IN-
IN+
IN-
MAX4198
MAX4199
MAX4198
MAX4199
MAX4198
MAX4199
V
V
V
V
CC
EE
CC
EE
V
V
CC
EE
REF
REF
REF
FB
OUT
FB
OUT
V
(MAX4198)
V
(MAX4199)
FB
OUT
OUT
OUT
V
V
OUT
OUT
= (V
= 10 (V
R
= -V
= -10V
ISO
B
- V
C
V
B
A
OUT
L
A
- V
(MAX4198)
)
A
V
A
OUT
(MAX4199)
)
OUTPUT
R
L