MAX1416EVC16 Maxim Integrated, MAX1416EVC16 Datasheet - Page 2

• Manufacturer Part Number: MAX1416EVC16
• Description: Analog to Digital Converters - ADC MAX1416 Evaluation Kit/Evaluation System
• Manufacturer: Maxim Integrated

Specifications of MAX1416EVC16

• Number Of Channels: 2
• Architecture: Sigma-Delta
• Conversion Rate: 0.5 KSPs
• Resolution: 16 bit
• Input Type: Differential
• Interface Type: QSPI, Serial (SPI, Microwire)
• Operating Supply Voltage: 4.75 V to 5.25 V
• Maximum Power Dissipation: 762 mW
• Number Of Converters: 1
• Voltage Reference: 3.5 V

MAX1416 Evaluation Kit/Evaluation System
Note: Indicate that you are using the MAX1416 when contacting these component suppliers.
Before beginning, the following equipment is needed:
• MAX1416 EV system:
• DC power supply, +7VDC to +12VDC at 0.25A
• DC power supply, +5VDC
• A user-supplied Windows 2000/XP computer with an
Note: In the following sections, software-related items
are identified by bolding. Text in bold refers to items
directly from the EV kit software. Text in bold and
underlined refers to items from the Windows 2000/XP
operating system.
The MAX1416 EV kit is fully assembled and tested.
Follow the steps below to verify board operation.
Caution: Do not turn on the power until all connec-
tions are completed.
1) Visit the Maxim website (www.maxim-ic.com) to
2) Ensure that jumpers JU1, JU2, and JU4 are closed
3) Carefully connect the boards by aligning the 40-pin
4) Connect the +5VDC power source to the MAX1416
2
Taiyo Yuden
TDK Corp.
available USB port to connect to the USBTO232
board
_______________________________________________________________________________________
download the latest version of the USBTO232 User
Guide. Follow the steps in the USBTO232 User Guide
Quick Start section and return to step 2 of this Quick
Start section when finished.
and that jumper JU3 is in the 1-2 position (see Table
1 for jumper settings).
header of the MAX1416 EV kit with the 40-pin con-
nector of the 68HC16MODULE-DIP module. Gently
press them together. The two boards should be flush
against one another.
EV kit at terminal block TB1. Observe the polarity
marked on the board.
Recommended Equipment (USB Port/PC
MAX1416 EV kit
68HC16MODULE-DIP
USBTO232 (USB cable included)
SUPPLIER
Connection Option)
800-348-2496
847-803-6100
PHONE
Quick Start
Procedure
5) Connect the +7VDC to +20VDC power source to the
6) Connect
7) The MAX1416 EV kit software should have already
8) Start the MAX1416 program by opening its icon in the
9) Turn on the power supplies and slide SW1 to the ON
10) When the main window appears (Figure 1), click
11) Apply input signals between AIN1+ and AIN1-. Tie
Before beginning, the following equipment is needed:
• MAX1416 EV system:
• DC power supply, +7VDC to +12VDC at 0.25A
• DC power supply, +5VDC
• A user-supplied Windows 98/2000/XP computer with
• 9-pin I/O extension cable
Note: In the following sections, software-related items are
identified by bolding. Text in bold refers to items directly
from the EV kit software. Text in bold and underlined
refers to items from the Windows 98/2000/XP operating
system.
Recommended Equipment (RS-232-to-COM
an available serial (COM) port
847-925-0899
847-390-4405
µC module at the terminal block located next to the
ON/OFF switch, along the top-edge of the µC mod-
ule. Observe the polarity marked on the board.
68HC16MODULE-DIP module if you have not done
so already.
been downloaded and installed in the USBTO232
Quick Start.
Start | Programs menu.
position on the 68HC16MODULE-DIP module. Press
the OK button to automatically connect and down-
load the KIT1416.C16 file to the module.
Initialize and then Calibrate.
the unused analog input (AIN2+ and AIN2-) to GND.
Click Read or check Auto Read. Observe the code
and voltage readout on the screen.
MAX1416 EV kit
68HC16MODULE-DIP
FAX
the
Component Suppliers
Port/PC Connection Option)
USBTO232
www.t-yuden.com
www.component.tdk.com
WEBSITE
board
to
the