MAX1124EGK-D Maxim Integrated, MAX1124EGK-D Datasheet - Page 11
![no-image](/images/no-image-200.jpg)
MAX1124EGK-D
Manufacturer Part Number
MAX1124EGK-D
Description
Analog to Digital Converters - ADC
Manufacturer
Maxim Integrated
Datasheet
1.MAX1124EGK-D.pdf
(17 pages)
Specifications of MAX1124EGK-D
Number Of Channels
1
Architecture
Pipeline
Conversion Rate
250000 KSPs
Resolution
10 bit
Input Type
Single-Ended/Differential
Snr
57.1 dB
Interface Type
LVDS, Parallel
Operating Supply Voltage
1.7 V to 1.9 V
Maximum Operating Temperature
+ 85 C
Package / Case
QFN EP
Maximum Power Dissipation
657 mW
Minimum Operating Temperature
- 40 C
Number Of Converters
1
Voltage Reference
Internal, External
INP and INN are the fully differential inputs of the
MAX1124. Differential inputs usually feature good rejec-
tion of even-order harmonics, which allows for enhanced
AC performance as the signals are progressing through
the analog stages. The MAX1124 analog inputs are self-
biased at a common-mode voltage of 1.4V and allow a
differential input voltage swing of 1.25V
are self-biased through 2.2kΩ resistors, resulting in a
typical differential input resistance of 4.4kΩ. It is recom-
mended to drive the analog inputs of the MAX1124 in
AC-coupled configuration to achieve best dynamic per-
formance. See the AC-Coupled Analog Inputs section for
a detailed discussion of this configuration.
The MAX1124 features an internal 1.23V bandgap ref-
erence circuit (Figure 3), which, in combination with an
internal reference-scaling amplifier, determines the full-
scale range of the MAX1124. Bypass REFIO with a
0.1µF capacitor to AGND. To compensate for gain
errors or increase the ADC’s full-scale range, the volt-
age of this bandgap reference can be indirectly adjust-
ed by adding an external resistor (e.g., 100kΩ trim
potentiometer) between REFADJ and AGND or REFADJ
and REFIO. See the Applications Information section for
a detailed description of this process.
Figure 4. System and Output Timing Diagram
1.8V, 10-Bit, 250Msps Analog-to-Digital Converter
D0P/N–D9P/N
with LVDS Outputs for Wideband Applications
DCLKP
DCLKN
ORP/N
CLKN
CLKP
INN
INP
t
NOTE: THE ADC SAMPLES ON THE RISING EDGE OF CLKP. THE RISING EDGE OF DCLKP CAN BE USED TO EXTERNALLY LATCH THE OUTPUT DATA.
CPDL
- t
______________________________________________________________________________________
PDL
SAMPLING EVENT
~ 0.4 x t
On-Chip Reference Circuit
Analog Inputs (INP, INN)
SAMPLE
t
N
CPDL
t
AD
N - 8
t
with t
PDL
N - 8
SAMPLE
= 1/f
SAMPLE
P-P
SAMPLING EVENT
t
. Both inputs
LATENCY
N + 1
N - 7
N - 7
Designed for a differential LVDS clock input drive, it is
recommended to drive the clock inputs of the MAX1124
Figure 5. Simplified LVDS Output Architecture
N - 1
SAMPLING EVENT
N + 8
t
CH
t
CPDL
N
- t
PDL
N
2.2kΩ
V
OP
Clock Inputs (CLKP, CLKN)
t
CL
SAMPLING EVENT
2.2kΩ
V
ON
N + 9
N + 1
N + 1
OGND
OV
CC
11