DS28E05P+T Maxim Integrated, DS28E05P+T Datasheet
DS28E05P+T
Specifications of DS28E05P+T
Related parts for DS28E05P+T
DS28E05P+T Summary of contents
Page 1
... Analog Sensor Calibration ● Aftermarket Management of Consumables Ordering Information appears at end of data sheet. For related parts and recommended products to use with this part, refer to www.maximintegrated.com/DS28E05.related. 1-Wire is a registered trademark of Maxim Integrated Products, Inc. 19-6568; Rev 0; 12/12 Features ● Single-Contact 1-Wire Interface ● 112 Bytes User EEPROM with 1K Write Cycles ● Programmable Write Protection and OTP EPROM Emulation Modes for User Memory ● ...
Page 2
... MIN TYP MAX UNITS 2.97 3.63 V 300 1500 Ω 1500 µA 0. PUP 0 PUP 0 µs 13 µ µs 48 µ µ µ µ δ µ δ 2 µs RL 400 µ 1000 — 10 Years Maxim Integrated │ 2 ...
Page 3
... logic 0 level. ILMAX + t ). W0LMIN RECMIN + t - ε and t W1LMAX F over the entire V range. PUP PROG L 1-Wire EEPROM , R , 1-Wire timing, and PUP PUP to be detected as logic The actual ε, respectively. W0LMAX F to the input-high RLMAX F Maxim Integrated │ 3 ...
Page 4
... See Figure 3 for details. The 1-Wire CRC is generated using a polynomial generator consisting of a shift register and XOR gates as shown in Figure 4. 1-Wire EEPROM + 1 6 N.C. DS28E05 N.C. TSOC FUNCTION Figure 1 shows the relationships shows the hierarchic structure of the 1-Wire Maxim Integrated │ 4 ...
Page 5
... The polynomial Additional information about the 1-Wire Cyclic Redundancy Check is available in Application Note 27: Understanding and Using Cyclic Redundancy Checks with Maxim iButton® iButton is a registered trademark of Maxim Integrated Products, Inc. www.maximintegrated.com PARASITE POWER 1-Wire FUNCTION CONTROL MEMORY FUNCTION CONTROL USER EEPROM ...
Page 6
... Once a protection is activated, it cannot 1-Wire EEPROM 6TH 7TH 8TH STAGE STAGE STAGE INPUT DATA PURPOSE Segment 2 Segment 1 Segment MAN. ID/U. PPD PPC PPB Maxim Integrated │ (00h) (10h) (20h) (30h) (40h) (50h) (60h) PPA ...
Page 7
... Function commands also read-accessible as part of the 8th memory page. The family code is stored at the lower address (78h). Memory Memory Function Commands The memory function flowchart protocols to access the memory of the DS28E05. The memory is written in segments of 2 bytes. 1-Wire EEPROM (Figure 6) describes the Maxim Integrated │ 7 ...
Page 8
... BYTE AND FFh BYTE VALID? Y MASTER Tx 2 DATA BYTES MASTER Rx (READS BACK) 2 DATA BYTES AND VERIFIES DS28E05 INCREMENTS ADDRESS MASTER N COUNTER Tx FFh RELEASE BYTE? Y MASTER WAITS PROG MASTER Rx CS BYTE MASTER Y Tx RESET? N SEGMENT # MASTER Tx RESET? Y Maxim Integrated │ 8 ...
Page 9
... Bits 3:1: Starting Segment Selection (SEG #). These bits specify the location within the selected memory page where the writing begins. For pages valid segment numbers are 000b (start of memory page) to 111b (last segment of memory page). Valid segment numbers for page 7 are 000b, 001b, and 010b. www.maximintegrated.com BIT 4 BIT 3 BIT 2 SEG # 1-Wire EEPROM shows BIT 1 BIT 0 0 Maxim Integrated │ 9 ...
Page 10
... The 1-Wire port of the DS28E05 is open drain with an internal circuit equivalent to that shown in Figure 7. V PUP R PUP DATA RECEIVE Tx = TRANSMIT OPEN-DRAIN PORT PIN 1-Wire EEPROM BIT 2 BIT 1 DS28E05 1-Wire PORT Rx Tx 100 Ω MOSFET Maxim Integrated │ 10 BIT 0 ...
Page 11
... ROM ID. If more than one slave is present on the bus and, for example, a read command is issued following the Skip ROM com- mand, data collision occurs on the bus as multiple slaves transmit simultaneously (open-drain pulldowns produce a wired-AND result). Maxim Integrated │ 11 ...
Page 12
... BIT 0 MATCH DS28E05 Tx BIT 1 DS28E05 Tx BIT 1 MASTER Tx BIT BIT 1 MATCH DS28E05 Tx BIT 63 DS28E05 Tx BIT 63 MASTER Tx BIT BIT 63 MATCH MEMORY FUNCTIONS FLOWCHART (FIGURE 6) 1-Wire EEPROM A5h N N RESUME COMMAND MASTER Tx RESET? N Maxim Integrated │ 12 ...
Page 13
... F is crossed, the TH Figure 10 , the DS28E05 starts its internal timing TL threshold before the write expired. For a write-zero time W1L(MAX) IL(MAX window. After the V threshold has W1L TH MASTER Rx "PRESENCE PULSE" t REC t RSTH DS28E05 Maxim Integrated │ 13 through PUP . MSP illustrates is W0L(MIN) during the REC ...
Page 14
... MASTER SAMPLING WINDOW δ t SLOT MASTER line low; its internal timing generator determines when this pulldown ends and the voltage starts rising again. When responding with a 1, the DS28E05 does not hold the data until the TL line low at all, and the voltage starts rising as soon as t window, when RL is over. 1-Wire EEPROM ε t REC t REC DS28E05 Maxim Integrated │ ...
Page 15
... Communication Examples See Table 5 legend and data direction codes. DESCRIPTION 1-Wire EEPROM V PUP negative glitch crosses not recognized (Figure 11). TL and Table 6 for the 1-Wire communication Maxim Integrated │ ...
Page 16
... Invalid parameter byte RST PD Select Ordering Information PART TEMP RANGE DS28E05R+T* -40ºC to +85ºC DS28E05P+ -40ºC to +85ºC DS28E05P+T -40ºC to +85ºC +Denotes a lead(Pb)-free/RoHS-compliant package Tape and reel. *Future product—contact factory for availability. www.maximintegrated.com WM PB FFh Data Data Release ...
Page 17
... Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed ...