MAX4361EUA-T Maxim Integrated, MAX4361EUA-T Datasheet - Page 9
![no-image](/images/no-image-200.jpg)
MAX4361EUA-T
Manufacturer Part Number
MAX4361EUA-T
Description
High Speed Operational Amplifiers ADSL Driver/Receiver
Manufacturer
Maxim Integrated
Datasheet
1.MAX4361EUA-T.pdf
(13 pages)
The MAX4361/MAX4362/MAX4363 should be powered
from a well-regulated, low-noise, 4.5V to 5.5V supply in
order to optimize the ADSL upstream drive capability to
+12.5dBm and maintain the best SFDR.
High-quality capacitors with low equivalent series resis-
tance (ESR) such as multilayer ceramic capacitors
(MLCCs) should be used to minimize supply voltage
ripple and power dissipation. A larger capacitor located
in proximity to the MAX4361/MAX4362/MAX4363
improves decoupling for lower frequency signals.
In addition, 0.1µF MLCC decoupling capacitors should
be located as close as possible to each of the power-
supply pins, no more than 1/8 inch away. An additional
large (4.7µF to 10µF) tantalum capacitor should be
placed on the board near the supply terminals to sup-
ply current for fast, large-signal changes at the
MAX4361/MAX4362/MAX4363 outputs.
The MAX4361/MAX4362 require a single 0.1µF bypass
from V+ to ground located as close as possible to the
IC leads.
The MAX4363 features separate supply and ground
pins for the receiver and driver amplifiers. Bypass the
V+ (RX) supply to the GND (RX) pin with a 0.1µF capaci-
tor. Bypass the V+ (TX) supply to the GND (TX) pin with
a separate 0.1µF capacitor. Both capacitors should be
placed as close as possible to their respective IC leads.
The 5V supplied at the universal serial bus (USB) port
may be poorly regulated or unable to supply the peak
currents required by an ADSL modem. Improving the
quality of the supply will optimize the performance of
the MAX4361/MAX4362/MAX4363 in a USB-supplied
CPE ADSL modem. This can be accomplished through
the use of a step-up DC-to-DC converter or switching
power supply followed by a low-dropout (LDO) regula-
tor. Careful attention must be paid to decoupling the
power supply at the output of the DC-to-DC converter,
the output of the LDO regulator and the supply pins of
the MAX4361/MAX4362/MAX4363.
The MAX4361/MAX4362/MAX4363 are capable of dri-
ving capacitive loads up to 2nF. Most hybrid circuits
are well under this limit. For additional capacitive-drive
capability use isolation resistors between the output
ADSL Drivers/Receivers for Customer Premise
Applications Information
Power Supply and Decoupling
_______________________________________________________________________________________
Driving a Capacitive Load
USB Applications
MAX4361/MAX4362
MAX4363
and the load to reduce ringing on the output signal. In a
typical hybrid the back-matching resistors provide suffi-
cient isolation for most any capacitive-loading condition
(see Figure 1).
To operate an amplifier on a single-voltage supply, a
voltage midway between the supply and ground must be
generated to properly bias the inputs and the outputs.
A voltage divider can be created with two equal-value
resistors (Figure 2). There is a trade-off between the
power consumed by the divider and the voltage drop
across these resistors due to the positive input bias
currents. Selecting 2.7kΩ for R1 and R2 will create a
voltage divider that draws less than 1mA from a 5V
supply. Use a decoupling capacitor (0.1µF) at the node
where V
It is important to consider the total power dissipation of
the MAX4361/MAX4362/MAX4363 in order to properly
size the heat sink area of an application. With some
simplifying assumptions we can estimate the total
power dissipated in the driver (see Typical Operating
Figure 1. Driving Capacitive Load
Figure 2. Voltage-Divider Reference
REF
500Ω
Method for Generating a Midsupply
INPUT
is generated.
2.7kΩ
2.7kΩ
R1
R2
MAX436 _
5V
1kΩ
Equipment
Power Dissipation
3.1Ω
0.1µF
V
REF
C
LOAD
OUTPUT
Voltage
9