MAX4415EUA Maxim Integrated, MAX4415EUA Datasheet - Page 17
![no-image](/images/no-image-200.jpg)
MAX4415EUA
Manufacturer Part Number
MAX4415EUA
Description
High Speed Operational Amplifiers Integrated Circuits (ICs)
Manufacturer
Maxim Integrated
Datasheet
1.MAX4418EUD.pdf
(22 pages)
Specifications of MAX4415EUA
Number Of Channels
1
Voltage Gain Db
93 dB
Input Offset Voltage
0.5 mV (Typ) at 5.5 V
Slew Rate
470 V/us at 5 V
Operating Supply Voltage
3 V, 5 V
Maximum Operating Temperature
+ 85 C
Package / Case
uMAX
Common Mode Rejection Ratio (min)
65 dB
Gain Bandwidth Product
150 MHz
Maximum Power Dissipation
362 mW
Minimum Operating Temperature
- 40 C
Factory Pack Quantity
50
Supply Voltage - Max
5.5 V
Supply Voltage - Min
2.7 V
The MAX4414–MAX4419 are designed to minimize dif-
ferential gain error and differential phase error to 0.03%/
0.15° respectively, making them ideal for driving video
loads. See Figure 4.
The low distortion and high bandwidth of the
MAX4414–MAX4419 make them ideal for use in active
filter circuits. Figure 5 is a 15MHz lowpass, multiple-
feedback active filter using the MAX4414.
Input buffer amplifiers can be a source of significant
errors in high-speed ADC applications. The input buffer
is usually required to rapidly charge and discharge the
ADC’s input, which is often capacitive (see Output
Capacitive Loading and Stability). In addition, since a
high-speed ADC’s input impedance often changes very
rapidly during the conversion cycle, measurement
accuracy must be maintained using an amplifier with
very low output impedance at high frequencies. The
combination of high speed, fast slew rate, low noise,
and a low and stable distortion over load make the
MAX4414–MAX4419 ideally suited for use as buffer
amplifiers in high-speed ADC applications.
These amplifiers operate from a single +2.7V to +5.5V
power supply. Bypass V
capacitor as close to the pin as possible.
Layout and Power-Supply Bypassing
f
0
Low-Power, +3V/+5V, 400MHz Single-Supply
=
Q
2
=
1
π
______________________________________________________________________________________
×
GAIN
C
1
R
R
1
1
×
2
CC
=
+
C
×
2
R
R
R
C
R
3
1
to ground with a 0.1µF
×
2
2
1
2
×
Op Amps with Rail-to-Rail Outputs
1
R
+
Video Line Driver
ADC Input Buffer
2
C
R
1
×
1
3
Active Filters
×
R
C
3
2
Maxim recommends using microstrip and stripline tech-
niques to obtain full bandwidth. Design the PC board
for a frequency greater than 1GHz to prevent amplifier
performance degradation due to board parasitics.
Avoid large parasitic capacitances at inputs and out-
puts. Whether or not a constant-impedance board is
used, observe the following guidelines:
• Do not use wire-wrap boards due to their high induc-
• Do not use IC sockets because of the increased par-
• Use surface-mount instead of through-hole compo-
• Use a PC board with at least two layers; it should be
• Keep signal lines as short and as straight as possible.
Figure 4. Video Line Driver
tance.
asitic capacitance and inductance.
nents for better high-frequency performance.
as free from voids as possible.
Do not make 90° turns; round all corners.
75Ω
R
IN
TIN
MAX4414
24Ω
R
F
(R
L
= R
75Ω
R
TO
O
+ R
TO
)
Z
O
= 75Ω
V
OUT
R
75Ω
O
17