MAX3301EETJ Maxim Integrated, MAX3301EETJ Datasheet - Page 26

no-image

MAX3301EETJ

Manufacturer Part Number
MAX3301EETJ
Description
USB Interface IC
Manufacturer
Maxim Integrated
Datasheet

Specifications of MAX3301EETJ

Operating Supply Voltage
3 V to 4.5 V
Operating Supply Current
5 uA

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MAX3301EETJ+
Manufacturer:
Maxim
Quantity:
37
addressed at I
locations 16h, 17h) to support USB OTG SIE implemen-
tations that are limited to I
between 0h and 15h.
Table 17 provides the contents of the ID registers of the
MAX3301E/MAX3302E. Addresses 00h and 01h com-
prise the vendor ID registers. Addresses 02h and 03h
comprise the product ID registers. Addresses 14h and
15h comprise the revision ID registers.
Many cell phones are required to interface to car kits.
Depending upon the car kit, the interface to the phone
may be required to support any or all of the following
functions:
D+ and D- of the MAX3301E/MAX3302E go to a high-
impedance state when in shutdown mode, allowing
external signals (including audio) to be multiplexed onto
these lines.
USB On-the-Go Transceivers and Charge Pumps
26
Table 13. Interrupt-Enable High Register (Write to Address 0Eh to Set, Write to Address
0Fh to Clear)
BIT NUMBER
Audio input
Audio output
Charging
Control and status
______________________________________________________________________________________
0
1
2
3
4
5
6
7
ID and Manufacturer Register Address Map
2
C register location 10h, 11h (as well as
cr_int_sess_end
bdis_acon
SYMBOL
vbus_vld
sess_vld
id_float
id_gnd
dm_hi
dp_hi
2
C register addresses
Audio Car Kit
S et to 0 to d i sab l e the vb us_vld i nter rup t for a l ow - to- hi gh transiti on. S et to 1 to
enab l e the vb us_vld i nter rup t for a l ow - to- hi gh transiti on. S ee Tab l es 10 and 11.
S et to 0 to d i sab l e the sess_vld i nter rup t for a l ow - to- hi gh transiti on. S et to 1 to
enab l e the sess_vld i nter rup t for a l ow - to- hi gh transiti on. S ee Tab l es 10 and 11.
S et to 0 to d i sab l e the d p _hi i nter r up t for a l ow - to- hi g h tr ansi ti on. S et to 1 to
enab l e the d p _hi i nter r up t for a l ow - to- hi g h tr ansi ti on. S ee Tab l es 10 and 11.
S et to 0 to d i sab l e the i d _g nd i nter r up t for a l ow - to- hi g h tr ansi ti on. S et to 1 to
enab l e the i d _g nd i nter r up t for a l ow - to- hi g h tr ansi ti on. S ee Tab l es 10 and 11.
S et to 0 to d i sab l e the d m _hi i nter r up t for a l ow - to- hi g h tr ansi ti on. S et to 1 to
enab l e the d m _hi i nter r up t for a l ow - to- hi g h tr ansi ti on. S ee Tab l es 10 and 11.
S et to 0 to d i sab l e the i d _fl oat i nter r up t for a l ow - to- hi g h tr ansi ti on. S et to 1 to
enab l e the i d _fl oat i nter r up t for a l ow - to- hi g h tr ansi ti on. S ee Tab l es 10 and 11.
S et to 0 to d i sab l e the b d is_acon interr up t for a low - to- hig h tr ansi ti on. Set to 1 to
enab l e the b d is_acon interr up t for a low - to- hig h tr ansi ti on. See Tab l es 10 and 11.
S et to 0 to d i sab l e the cr _i nt_sess_end i nter r up t for a l ow - to- hi g h tr ansi ti on.
S et to 1 to enab l e the cr _i nt_sess_end i nter r up t for a l ow - to- hi g h tr ansi ti on.
S ee Tab l es 10 and 11.
Two external resistors (27.4Ω ±1%) are required for
USB connection. Install one resistor in series between
D+ of the MAX3301E/MAX3302E and D+ of the USB
connector. Install the other resistor in series between D-
of the MAX3301E/MAX3302E and D- of the USB con-
nector (see the Typical Operating Circuit ).
Five external capacitors are recommended for proper
operation. Install all capacitors as close to the device as
possible. Decouple V
capacitor. Bypass V
capacitor. Bypass TRM to GND with a 1µF (or greater)
ceramic or plastic capacitor. Connect a 100nF flying
capacitor between C+ and C- for the charge pump (see
the Typical Operating Circuit ). Bypass V
with a 1µF to 6.5µF ceramic capacitor in accordance
with USB OTG specifications.
To protect the MAX3301E/MAX3302E against ESD, D+,
D-, ID_IN, and V
ic electricity to protect the device up to ±15kV. The ESD
structures withstand high ESD in all states; normal oper-
CONTENTS
BUS
, have extra protection against stat-
CC
L
to GND with a 0.1µF ceramic
to GND with a 1µF ceramic
External Components
External Capacitors
External Resistors
ESD Protection
BUS
POWER-UP
VALUE AT
to GND
0
0
0
0
0
0
0
0

Related parts for MAX3301EETJ