MAX7349EVKIT Maxim Integrated, MAX7349EVKIT Datasheet - Page 2

• Manufacturer Part Number: MAX7349EVKIT
• Description: Interface - Specialized Evaluation Kit for the MAX7349/Emulates
• Manufacturer: Maxim Integrated
• Series: MAX7347, MAX7348, MAX7349r

Specifications of MAX7349EVKIT

• Product Type: Interfaced Low EMI Key Switch

Before you begin, you need the following equipment:
•
•
•
•
MAX7349 Evaluation Kit
MAXQ is a registered trademark of Maxim Integrated Products, Inc.
Note: Indicate that you are using the MAX7349 when contacting
these component suppliers.
2
Murata
Panasonic
Suntsu Frequency
Control
Taiyo Yuden
TDK
DESIGNATION
Maxim MAX7349 EV kit
USB-type A-B cable (included with MAX7349EVKIT)
Windows 98SE/2000/XP computer with a spare
USB port
Administrator privileges may be required when first
installing the device on Windows 2000/XP
_______________________________________________________________________________________
SUPPLIER
R22
R23
R24
R25
U1
U2
U3
U4
U5
U6
QTY
0
0
0
0
1
1
1
1
1
0
770-436-1300 www.murata.com
714-373-7366 www.panasonic.com
949-305-0220 www.suntsuinc.com
800-348-2496 www.t-yuden.com
847-803-6100 www.component.tdk.com
Component Suppliers
PHONE
21.5kΩ ±1% resistor (1206),
not installed
32.4kΩ ±1% resistor (1206),
not installed
21.5kΩ ±1% resistor (1206),
not installed
10Ω ±5% resistor (1206),
not installed
Maxim MAX7349AEG (24-pin QSOP)
FTDI FT232BM
(32-pin TQFP, 7mm x 7mm)
Maxim MAX8511EXK25-T
ADV top mark (5-pin SC70)
93C46 type 3-wire EEPROM
16-bit architecture (8-pin SO)
M axi m M AX Q2000- RAX ( 68- p i n Q FN )
Maxim MAX4366EUA+ (8-pin µMAX)
Required Equipment
DESCRIPTION
Quick Start
WEBSITE
Do not turn on the power until all connections are
made.
1) Ensure that the jumper settings are in the default
2) Install the evaluation software on your computer by
3) Connect the USB cable between the MAX7349 EV kit
4) During device driver installation, Windows XP
DESIGNATION
positions. See Table 1.
running the INSTALL.EXE program on the installa-
tion disk. The program files are copied and icons
are created for them in the Windows Start menu.
and the computer. When you plug in the MAX7349 EV kit
board for the first time, the Windows plug-and-play
system detects the new hardware and automatically
runs the Add New Hardware Wizard. (If the Add
New Hardware Wizard does not appear after one
minute, unplug the USB cable and plug it in again.)
Be sure to specify the search location. This EV kit is
based on the CMAXQUSB design, so the software
includes a copy of the device driver in the installed
software directory. Refer to Application Note 3601
Troubleshooting Windows Plug-and-Play and USB
for Maxim Evaluation Kits for more details.
shows a warning message, indicating that the
VR1
Y1
Y2
Y3
—
—
—
—
Component List (continued)
QTY
1
1
1
1
8
1
4
1
Volume control, 5kΩ
Panasonic EVL-HFAA01A53
16MHz crystal (HC49/US),
parallel resonant, 20pF load
Citizen HC49US16.000MABJ
ECS ECS-160-20-4
Suntsu SCS20B-16.000MHZ-I
6MHz crystal (HC49/US)
Citizen HC49US6.000MABJ
Suntsu SCS22B-6.000MHZ-I
32.768kHz watch crystal,
12.5pF cylindrical
Epson C-001R 32.7680K-A
Suntsu SCT3-32.768KHZ
Shunts
MAX7349 EV kit PC board
Rubber bumpers, 0.100in (H) x
0.400in (W) square
USB high-speed A-to-B cable,
5ft (1.5m)
DESCRIPTION
Procedure