MAX3420EECJ Maxim Integrated, MAX3420EECJ Datasheet - Page 12
![no-image](/images/no-image-200.jpg)
MAX3420EECJ
Manufacturer Part Number
MAX3420EECJ
Description
Peripheral Drivers & Components - PCIs
Manufacturer
Maxim Integrated
Datasheet
1.MAX3420EETG-T.pdf
(22 pages)
Specifications of MAX3420EECJ
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
TQFP-32
Minimum Operating Temperature
- 40 C
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX3420EECJ+
Manufacturer:
MAXIM
Quantity:
1 001
Company:
Part Number:
MAX3420EECJ+
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
MAX3420EECJ+T
Manufacturer:
Maxim Integrated
Quantity:
10 000
MAX3420E
12
The MAX3420E contains the digital logic and analog
circuitry necessary to implement a full-speed USB
peripheral that complies with the USB specification rev
2.0. ESD protection of ±15kV is provided on D+, D-,
and VBCOMP. The MAX3420E features an internal USB
transceiver and an internal 1.5kΩ resistor that connects
between D+ and V
(CONNECT). This allows a USB peripheral to control
the logical connection to the USB host. Any SPI master
can communicate with the MAX3420E through the SPI
slave interface that operates in SPI mode (0,0) or (1,1).
An SPI master accesses the MAX3420E by reading and
writing to internal registers. A typical data transfer con-
sists of writing a first byte that sets a register address
and direction with additional bytes reading or writing
data to the register or internal FIFO.
The MAX3420E contains 384 bytes of endpoint buffer
memory, implementing the following endpoints:
The choice to use EP1, EP2, EP3 as BULK or INTER-
RUPT endpoints is strictly a function of the endpoint
descriptors that the SPI master returns to the USB host
during enumeration.
USB Peripheral Controller
with SPI Interface
(V
CC
• EP0: 64-byte bidirectional CONTROL endpoint
• EP3: 64-byte BULK/INT IN endpoint
• EP1: 2 x 64-byte double-buffered BULK/INT
• EP2: 2 x 64-byte double-buffered BULK/INT IN
OUT endpoint
endpoint
= +3.3V, V
L
= +3.3V, T
CC
under the control of a register bit
Detailed Description
A
= +25°C.)
-1
0
4
1
3
2
0
10
20
EYE DIAGRAM
30
TIME (ns)
40
The MAX3420E register set and SPI interface is optimized
to reduce SPI traffic. An interrupt output pin, INT, notifies
the SPI master when USB service is required: when a
packet arrives, a packet is sent, or the host suspends or
resumes bus activity. Double-buffered endpoints help
sustain bandwidth by allowing data to move concurrently
over USB and the SPI interface.
Power the USB transceiver by applying a positive 3.3V
supply to V
ceramic capacitor as close to the V
The MAX3420E digital core is powered though the V
pin. V
face and all other inputs and outputs. Connect V
system’s logic-level power supply. Internal level transla-
tors and V
pose inputs and outputs to operate at a system voltage
between 1.71V and 3.6V.
The MAX3420E features a USB V
VBCOMP. The VBCOMP pin can withstand input volt-
ages up to 6V. Bypass VBCOMP to GND with a 1.0µF
ceramic capacitor. According to USB specification rev
2.0, a self-powered USB device must not power the
1.5kΩ pullup resistor on D+ if the USB host turns off
V
comparator so that the SPI master can detect the loss
of V
Typical Operating Characteristics
BUS
50
BUS
. VBCOMP is internally connected to a voltage
L
also acts as a reference level for the SPI inter-
60
(through an interrupt (INT) or checking a bit
L
allow the SPI interface and all general-pur-
70
CC
. Bypass V
80
CC
to GND with a 1.0µF
CC
BUS
pin as possible.
detector input,
Maxim Integrated
VBCOMP
L
to the
V
CC
V
L
L