MAX9969ALCCQ+TD Maxim Integrated, MAX9969ALCCQ+TD Datasheet - Page 11
![no-image](/images/no-image-200.jpg)
MAX9969ALCCQ+TD
Manufacturer Part Number
MAX9969ALCCQ+TD
Description
Buffers & Line Drivers
Manufacturer
Maxim Integrated
Datasheet
1.MAX9969ALCCQD.pdf
(31 pages)
Specifications of MAX9969ALCCQ+TD
Rohs
yes
ELECTRICAL CHARACTERISTICS (continued)
(V
+85°C, unless otherwise noted. All temperature coefficients are measured at T
Note 1: All minimum and maximum DC and driver 3V rise- and fall-time test limits are 100% production tested. All other test limits
Note 2: Total for dual device at worst-case setting.
Note 3: Does not include above ground internal dissipation of the comparator outputs. Additional power dissipation is typically
Note 4: Externally forced voltages may exceed this range provided that the Absolute Maximum Ratings are not exceeded.
Note 5: Transition time from LLEAK being asserted to leakage current dropping below specified limits.
Note 6: Based on simulation results only.
Note 7: Transition time from LLEAK being deasserted to output returning to normal operating mode.
Note 8: With the exception of offset and gain/CMRR tests, reference input values are calibrated for offset and gain.
Note 9: Specifications measured at the endpoints of the full range. Full range is -1.3V ≤ V
Note 10: Relative to straight line between 0 and 4.5V.
Note 11: Change in offset voltage with power supplies independently set to their minimum and maximum values.
Note 12: Nominal target value is 50Ω. Contact factory for alternate trim selections within the 45Ω to 51Ω range.
Note 13: V
Note 14: Measured from the crossing point of DATA_ inputs to the settling of the driver output.
Note 15: Prop delays are measured from the crossing point of the differential input signals to the 50% point of the expected output
Note 16: Rising edge to rising edge or falling edge to falling edge.
Note 17: Specified amplitude is programmed. At this pulse width, the output reaches at least 90% of its nominal (DC) amplitude. The
Note 18: Specified amplitude is programmed. Maximum data rate is specified in transitions per second. A square wave that reaches
Note 19: Crosstalk from either driver to the other. Aggressor channel is driving 3V
Note 20: Indicative of switching speed from DHV_ or DLV_ to DTV_ and DTV_ to DHV_ or DLV_ when V
Note 21: Change in offset voltage over the input range.
AC CHARACTERISTICS (Z
Enable Time
Disable Time
Current Settling Time on
Commutation
Spike During Enable/Disable
Transition
CC
= +9.75V, V
are guaranteed by design. Tests are performed at nominal supply voltages, unless otherwise noted.
(32mA x V
-1.5V ≤ V
swing. Rise time of the differential inputs DATA_ and RCV_ are 250ps (10% to 90%).
pulse width is measured at DATA_.
at least 90% of its programmed amplitude may be generated at one-half of this frequency.
with V
V
PARAMETER
DTV_
DTV_
DTV_
= midpoint of voltage swing, R
< V
EE
DTV_
DLV_
VCCO_
= -4.75V, V
= +1.5V.
______________________________________________________________________________________
≤ +6.5V.
or V
)
L
DTV_
= 50Ω to GND)
CCO_
> V
Driver/Comparator with 35mA Load
SYMBOL
DHV_
= +2.5V, SC1 = SC0 = 0, V
t
t
DIS
EN
Dual, Low-Power, 1200Mbps ATE
, switching speed is degraded by a factor of approximately 3.
S
= 50Ω. Measurement is made using the comparator.
(Note 26)
(Note 26)
I
1mA (Note 27)
I
20mA (Note 27)
I
SOURCE
SOURCE
SOURCE
= I
= I
= I
SINK
SINK
SINK
CONDITIONS
CPHV_
=
=
= 35mA, V
= +7.2V, V
I
V
I
V
I
V
I
V
To 10%
To 1.5%
To 10%
To 1.5%
SOURCE
SINK
SOURCE
SINK
COM
COM
COM
COM
J
COM
= 10mA,
= 10mA,
_ = -1V
_ = 1V
_ = 1V
_ = -1V
= +60°C to +100°C, unless otherwise noted.) (Note 1)
= 10mA,
= 10mA,
_ = 0
P-P
CPLV_
into a 50Ω load. Victim channel is in term mode
= -2.2V, V
DHV_
MIN
1.7
1.7
3
3
LDH
≤ +6.5V, -1.5V ≤ V
_ = V
TYP
DLV_
200
3.5
3.5
15
50
15
2
2
3
LDL
_ = 0, V
< V
MAX
DTV_
300
2.3
2.3
4
4
5
DLV_
GS
< V
= 0, T
≤ +6.3V,
UNITS
DHV_
mV
ns
ns
ns
J
. If
11
=