MC74LCX16244DT ON Semiconductor, MC74LCX16244DT Datasheet - Page 7

• Manufacturer Part Number: MC74LCX16244DT
• Description: Buffers & Line Drivers 2-36.V CMOS 16-Bit
• Manufacturer: ON Semiconductor

Specifications of MC74LCX16244DT

• Product Category: Buffers & Line Drivers
• Number Of Input Lines: 16
• Number Of Output Lines: 3
• Polarity: Non-Inverting
• Supply Voltage - Max: 3.6 V
• Supply Voltage - Min: 2 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: TSSOP-48
• High Level Output Current: - 24 mA
• Logic Family: LCX
• Logic Type: CMOS
• Low Level Output Current: 24 mA
• Maximum Power Dissipation: 200 mW
• Minimum Operating Temperature: - 40 C
• Number Of Channels Per Chip: 16
• Output Type: 3-State
• Propagation Delay Time: 5.2 ns at 2.7 V, 4.5 ns at 3.3 V
• Factory Pack Quantity: 39

PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
−T−
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [e-mail]
ON Semiconductor and
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
0.076 (0.003)
SEATING
PLANE
PIN 1
IDENT.
D
L
C
48
1
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
48X
K
0.12 (0.005)
REF
−V−
A
G
1
M
T
0.32
48X
U
S
N. American Technical Support: 800−282−9855 Toll Free
Europe, Middle East and Africa Technical Support:
Japan Customer Focus Center
PACKAGE DIMENSIONS
SOLDERING FOOTPRINT
USA/Canada
Phone: [phone]
Phone: 81−3−5817−1050
V
S
RECOMMENDED
http://onsemi.com
25
24
DT SUFFIX
CASE 1201
TSSOP−48
−U−
B
ISSUE B
H
7
N
J
DETAIL E
DETAIL E
N
PITCH
0.50
Ç Ç Ç
É É É
J1
Ç Ç Ç
É É É
SECTION N−N
F
DIMENSIONS: MILLIMETERS
K1
K
0.25 (0.010)
M
1.00
−W−
48X
8.45
NOTES:
1. DIMENSIONING AND TOLERANCING PER
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
4. DIMENSION K DOES NOT INCLUDE DAMBAR
5. TERMINAL NUMBERS ARE SHOWN FOR
6. DIMENSIONS A AND B ARE TO BE
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
ANSI Y14.5M, 1982.
MOLD FLASH, PROTRUSIONS OR GATE
BURRS. MOLD FLASH OR GATE BURRS
SHALL NOT EXCEED 0.15 (0.006) PER SIDE.
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL
IN EXCESS OF THE K DIMENSION AT
MAXIMUM MATERIAL CONDITION.
REFERENCE ONLY.
DETERMINED AT DATUM PLANE −W−.
DIM
K1
J1
A
B
C
D
G
H
K
M
F
J
L
12.40
MILLIMETERS
MIN
6.00
0.05
0.50
0.37
0.09
0.09
0.17
0.17
7.95
−−−
0.50 BSC
0
_
12.60
MAX
6.20
1.10
0.15
0.75
0.20
0.16
0.27
0.23
8.25
−−−
MC74LCX16244/D
8
_
0.488
0.236
0.002
0.020
0.015
0.004
0.004
0.007
0.007
0.313
MIN
0.0197 BSC
−−−
0
INCHES
_
0.496
0.244
0.043
0.006
0.030
0.008
0.006
0.009
0.325
0.011
MAX
−−−
8
_