MAX8734AEEI+TG104 Maxim Integrated, MAX8734AEEI+TG104 Datasheet - Page 20
![no-image](/images/no-image-200.jpg)
MAX8734AEEI+TG104
Manufacturer Part Number
MAX8734AEEI+TG104
Description
Current & Power Monitors & Regulators High-Efficiency Quad-Output Main Power-Supply Controllers for Notebook Computers
Manufacturer
Maxim Integrated
Datasheet
1.MAX8734AEEIG104.pdf
(33 pages)
Specifications of MAX8734AEEI+TG104
Product
Power Monitors
Supply Voltage - Max
24 V
Supply Voltage - Min
4.5 V
Operating Temperature Range
- 40 C to + 85 C
Accuracy
1.50%
Input Voltage Range
4.5 V to 24 V
Supply Current
50 uA
High-Efficiency, Quad-Output, Main Power-
Supply Controllers for Notebook Computers
The 2V reference (REF) is accurate to ±1% over tem-
perature, making REF useful as a precision system
reference. Bypass REF to GND with a 0.22µF (min)
capacitor. REF can supply up to 100µA for external
loads. However, if extremely accurate specifications for
both the main output voltages and REF are essential,
avoid loading REF. Loading REF reduces the LDO5,
LDO3, OUT5, and OUT3 output voltages slightly
because of the reference load-regulation error.
Two internal regulators produce 5V (LDO5) and 3.3V
(LDO3). LDO5 provides gate drive for the external
MOSFETs and powers the PWM controller, logic, refer-
ence, and other blocks within the device. The LDO5
regulator supplies a total of 100mA for internal and
external loads, including MOSFET gate drive, which
typically varies from 10mA to 50mA, depending on
switching frequency and the external MOSFETs. LDO3
powers up when the reference (REF) is in regulation,
and supplies up to 100mA for external loads. Bypass
LDO5 and LDO3 with a minimum 4.7µF load; use an
additional 1µF per 5mA of internal and external load.
When the 5V main output voltage is above the LDO5
bootstrap-switchover threshold, an internal 1.4Ω p-chan-
nel MOSFET switch connects OUT5 to LDO5 while simul-
taneously shutting down the LDO5 linear regulator.
Similarly, when the 3.3V main output voltage is above the
LDO3 bootstrap-switchover threshold, an internal 1.5Ω
p-channel MOSFET switch connects OUT3 to LDO3 while
simultaneously shutting down the LDO3 linear regulator.
These actions bootstrap the device, powering the internal
circuitry and external loads from the output SMPS volt-
ages, rather than through linear regulators from the bat-
Figure 6. Ultrasonic Current Waveforms
20
______________________________________________________________________________________
0
Reference and Linear Regulators
I
SONIC
40µs (MAX)
(REF, LDO5, and LDO3)
ZERO-CROSSING
DETECTION
ON-TIME (t
ON
)
INDUCTOR
CURRENT
tery. Bootstrapping reduces power dissipation due to
gate charge and quiescent losses by providing power
from a 90%-efficient switch-mode source, rather than
from a much-less-efficient linear regulator.
The current-limit circuit employs a “valley” current-sens-
ing algorithm. The MAX8734A uses the on-resistance of
the synchronous rectifier, while the MAX8732A/
MAX8733A use a discrete resistor in series with the
source of the synchronous rectifier as a current-sensing
element. If the magnitude of the current-sense signal at
CS_ (MAX8732A/MAX8733A)/LX_ (MAX8734A) is above
the current-limit threshold, the PWM is not allowed to initi-
ate a new cycle (Figure 7). The actual peak current is
greater than the current-limit threshold by an amount
equal to the inductor ripple current. Therefore, the exact
current-limit characteristic and maximum load capability
are a function of the current-limit threshold, inductor
value, and input and output voltage.
For the MAX8732A/MAX8733A, connect CS_ to the
junction of the synchronous rectifier source and a cur-
rent-sense resistor to GND. With a current-limit threshold
of 100mV, the accuracy is approximately ±7%. Using a
lower current-sense threshold results in less accuracy.
The current-sense resistor only dissipates power when
the synchronous rectifier is on.
For lower power dissipation, the MAX8734A uses the
on-resistance of the synchronous rectifier as the cur-
rent-sense element. Use the worst-case maximum
value for R
add some margin for the rise in R
ture. A good general rule is to allow 0.5% additional
resistance for each °C of temperature rise. The current
limit varies with the on-resistance of the synchronous
rectifier. The reward for this uncertainty is robust, loss-
less overcurrent sensing. When combined with the
Figure 7. “Valley” Current-Limit Threshold Point
DS(ON)
0
from the MOSFET data sheet, and
Current-Limit Circuit (ILIM_)
TIME
DS(ON)
-I
PEAK
I
I
with tempera-
LOAD
LIMIT