24VL014H/SN Microchip Technology, 24VL014H/SN Datasheet - Page 7

• Manufacturer Part Number: 24VL014H/SN
• Description: IC EEPROM 1KBIT 400KHZ 8SOIC
• Manufacturer: Microchip Technology

Specifications of 24VL014H/SN

• Memory Size: 1K (128 x 8)
• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Speed: 100kHz, 400kHz
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 1.5 V ~ 3.6 V
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Memory Configuration: 128 X 8 / 64 X 16
• Ic Interface Type: I2C
• Clock Frequency: 400kHz
• Supply Voltage Range: 1.5V To 3.6V
• Memory Case Style: SOIC
• No. Of Pins: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

4.0
The following bus protocol has been defined:
• Data transfer may be initiated only when the bus
• During data transfer, the data line must remain
Accordingly, the following bus conditions have been
defined (Figure 4-1).
4.1
Both data and clock lines remain high.
4.2
A high-to-low transition of the SDA line while the clock
(SCL) is high determines a Start condition. All
commands must be preceded by a Start condition.
4.3
A low-to-high transition of the SDA line while the clock
(SCL) is high determines a Stop condition. All
operations must be ended with a Stop condition.
4.4
The state of the data line represents valid data when,
after a Start condition, the data line is stable for the
duration of the high period of the clock signal.
FIGURE 4-1:
FIGURE 4-2:
© 2008 Microchip Technology Inc.
SCL
SDA
is not busy.
stable whenever the clock line is high. Changes in
the data line while the clock line is high will be
interpreted as a Start or Stop condition.
SCL
SDA
(A)
BUS CHARACTERISTICS
Bus Not Busy (A)
Start Data Transfer (B)
Stop Data Transfer (C)
Data Valid (D)
Transmitter must release the SDA line at this point allowing
the Receiver to pull the SDA line low to acknowledge the
previous eight bits of data.
Condition
Start
(B)
1
DATA TRANSFER SEQUENCE ON THE SERIAL BUS CHARACTERISTICS
ACKNOWLEDGE TIMING
2
Data from transmitter
3
4
Acknowledge
Address or
Valid
5
(C)
6
to Change
Allowed
7
Data
Acknowledge
The data on the line must be changed during the low
period of the clock signal. There is one bit of data per
clock pulse.
Each data transfer is initiated with a Start condition and
terminated with a Stop condition. The number of the
data bytes transferred between the Start and Stop
conditions is determined by the master device and is,
theoretically, unlimited, though only the last sixteen will
be stored when doing a write operation. When an
overwrite does occur, it will replace data in a first-in
first-out fashion.
4.5
Each receiving device, when addressed, is required to
generate an acknowledge after the reception of each
byte. The master device must generate an extra clock
pulse which is associated with this Acknowledge bit.
The device that acknowledges has to pull down the
SDA line during the Acknowledge clock pulse in such a
way that the SDA line is stable low during the high
period of the acknowledge-related clock pulse. Of
course, setup and hold times must be taken into
account. A master must signal an end of data to the
slave by not generating an Acknowledge bit on the last
byte that has been clocked out of the slave. In this case,
the slave must leave the data line high to enable the
master to generate the Stop condition (Figure 4-2).
8
Note:
Bit
9
Acknowledge
The 24VL014H does not generate any
Acknowledge
programming cycle is in progress.
(D)
Data from transmitter
1
Receiver must release the SDA line at this
point so the Transmitter can continue
sending data.
2
24VL014H
3
bits
if
DS22116A-page 7
an
Condition
Stop
(C)
internal
(A)