24VL024H/SN Microchip Technology, 24VL024H/SN Datasheet - Page 9

• Manufacturer Part Number: 24VL024H/SN
• Description: IC EEPROM 2KBIT 400KHZ 8SOIC
• Manufacturer: Microchip Technology

Specifications of 24VL024H/SN

• Memory Size: 2K (256 x 8)
• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Speed: 100kHz, 400kHz
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 1.5 V ~ 3.6 V
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Memory Configuration: 256 X 8
• Ic Interface Type: I2C
• Clock Frequency: 400kHz
• Supply Voltage Range: 1.5V To 3.6V
• Memory Case Style: SOIC
• No. Of Pins: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

6.0
6.1
Following the Start signal from the master, the device
code (4 bits), the Chip Select bits (3 bits) and the R/W
bit (which is a logic low) are placed onto the bus by the
master transmitter. The device will acknowledge this
control byte during the ninth clock pulse. The next byte
transmitted by the master is the word address and will
be written into the Address Pointer of the 24VL024H.
After receiving another Acknowledge signal from the
24VL024H, the master device will transmit the data
word to be written into the addressed memory location.
The 24VL024H acknowledges again and the master
generates a Stop condition. This initiates the internal
write
generate Acknowledge
(Figure 6-1). If an attempt is made to write to the
protected portion of the array when the hardware write
protection has been enabled,
acknowledge the command, but no data will be written.
The write cycle time must be observed even if write
protection is enabled.
6.2
The write-control byte, word address and the first data
byte are transmitted to the 24VL024H in the same way
as in a byte write. But instead of generating a Stop
condition, the master transmits up to 15 additional data
bytes to the 24VL024H that are temporarily stored in
the on-chip page buffer and will be written into the
memory once the master has transmitted a Stop
condition. Upon receipt of each word, the four lower
order Address Pointer bits are internally incremented
by one.
FIGURE 6-1:
FIGURE 6-2:
© 2008 Microchip Technology Inc.
SDA Line
Bus Activity
Master
Bus Activity
SDA Line
Bus Activity
Master
Bus Activity
cycle
WRITE OPERATIONS
Byte Write
Page Write
and
S
T
A
R
T
S
S
S
T
A
R
T
BYTE WRITE
PAGE WRITE
the
signals
Control
Byte
Control
24VL024H
Byte
during
the
A
C
K
device will
Address (n)
this
will
Word
A
C
K
time
not
A
C
K
Address
Word
Data (n)
The higher order four bits of the word address remain
constant. If the master should transmit more than 16
bytes prior to generating the Stop condition, the
address counter will roll over and the previously
received data will be overwritten. As with the byte write
operation, once the Stop condition is received, an
internal write cycle will begin (Figure 6-2). If an attempt
is made to write to the protected portion of the array
when the hardware write protection has been enabled,
the device will acknowledge the command, but no data
will be written. The write cycle time must be observed
even if write protection is enabled.
6.3
The WP pin must be tied to V
half of the array will be write-protected (80h-FFh). If the
WP pin is tied to V
locations are allowed.
Note:
Write Protection
A
C
K
Page write operations are limited to writing
bytes within a single physical page,
regardless of the number of bytes
actually being written. Physical page
boundaries start at addresses that are
integer multiples of the page buffer size (or
‘page size’) and end at addresses that are
integer multiples of [page size – 1]. If a
Page Write command attempts to write
across a physical page boundary, the
result is that the data wraps around to the
beginning of the current page (overwriting
data previously stored there), instead of
being written to the next page, as might be
expected. It is therefore necessary that the
application software prevent page write
operations that would attempt to cross a
page boundary.
A
C
K
Data (n +1)
SS
, write operations to all address
Data
A
C
K
24VL024H
CC
or V
Data (n + 15)
SS
DS22109A-page 9
. If tied to V
A
C
K
P
S
T
O
P
A
C
K
S
T
O
P
P
CC
,