24VL025/SN Microchip Technology, 24VL025/SN Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
24VL025/SN
Manufacturer Part Number
24VL025/SN
Description
IC EEPROM 2KBIT 400KHZ 8SOIC
Manufacturer
Microchip Technology
Datasheet
1.24VL024TMNY.pdf
(30 pages)
Specifications of 24VL025/SN
Memory Size
2K (256 x 8)
Package / Case
8-SOIC (3.9mm Width)
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Speed
100kHz, 400kHz
Interface
I²C, 2-Wire Serial
Voltage - Supply
1.5 V ~ 3.6 V
Operating Temperature
-20°C ~ 85°C
Organization
256 K x 8
Interface Type
2-Wire
Maximum Clock Frequency
0.1 MHz
Access Time
3500 ns
Supply Voltage (max)
3.6 V
Supply Voltage (min)
1.5 V
Maximum Operating Current
3 mA
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 20 C
Operating Supply Voltage
1.8 V , 2.5 V , 3.3 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
24VL025/SN
Manufacturer:
MICROCHIP
Quantity:
12 000
2.0
The descriptions of the pins are listed in Table 2-1.
TABLE 2-1:
2.1
This is a bidirectional pin used to transfer addresses
and data into and out of the device. It is an open drain
terminal. Therefore, the SDA bus requires a pull-up
resistor to V
400 kHz).
For normal data transfer, SDA is allowed to change
only during SCL low. Changes during SCL high are
reserved for indicating the Start and Stop conditions.
2.2
The SCL input is used to synchronize the data transfer
to and from the device.
2.3
The A0, A1 and A2 inputs are used by the 24VL024/
24VL025 for multiple device operations. The levels on
these inputs are compared with the corresponding bits
in the slave address. The chip is selected if the
compare is true.
Up to eight 24VL024/24VL025 devices (four for the
SOT-23 package) may be connected to the same bus
by using different Chip Select bit combinations. These
inputs must be connected to either V
In most applications, the chip address inputs A0, A1
and A2 are hard-wired to logic ‘0’ or logic ‘1’. For
applications in which these pins are controlled by a
microcontroller or other programmable device, the chip
address pins must be driven to logic ‘0’ or logic ‘1’
before normal device operation can proceed.
© 2009 Microchip Technology Inc.
A0
A1
A2
V
SDA
SCL
WP
V
SS
CC
Name
PIN DESCRIPTIONS
SDA Serial Data
SCL Serial Clock
A0, A1, A2
CC
8-pin
PDIP
(typical 10 kΩ for 100 kHz, 2 kΩ for
1
2
3
4
5
6
7
8
PIN FUNCTION TABLE
8-pin
SOIC
1
2
3
4
5
6
7
8
CC
TSSOP
8-pin
or V
1
2
3
4
5
6
7
8
SS
.
MSOP
8-pin
1
2
3
4
5
6
7
8
TDFN
8-pin
2.4
WP is the hardware write-protect pin. It must be tied to
V
is enabled and will protect the entire array (00h-FFh). If
the WP pin is tied to V
is disabled.
2.5
The 24VL024/24VL025 employs a V
detector circuit that disables the internal erase/write
logic if the V
The SCL and SDA inputs have Schmitt Trigger and
filter circuits that suppress noise spikes to assure
proper device operation even on a noisy bus.
1
2
3
4
5
6
7
8
CC
or V
24VL024/24VL025
SS
WP (24VL024 only)
Noise Protection
SOT-23
6-pin
. If tied to V
CC
—
—
5
4
2
3
1
6
is below 1.0 volts at nominal conditions.
User Configurable Chip Select
User Configurable Chip Select
User Configurable Chip Select
Ground
Serial Data
Serial Clock
Write-Protect Input
+1.5V to 3.6V
CC
SS
, the hardware write protection
the hardware write protection
Function
DS22130A-page 5
CC
threshold