AP2141DSG-13 Diodes Inc., AP2141DSG-13 Datasheet - Page 11

• Manufacturer Part Number: AP2141DSG-13
• Description: Power Switch ICs - USB 0.5A SINGLE CH USB 2.0 Switch 90mOhm
• Manufacturer: Diodes Inc.

Specifications of AP2141DSG-13

• Product Category: Power Switch ICs - USB
• Rohs: yes

resistance of 100Ω. Hence, the output voltage drops down to zero. The time taken for discharge is dependent on the RC time constant of the
resistance and the output capacitor.
are removed. Connecting a heavy capacitive load to the output of the device can cause a momentary Over-current condition, which does not trigger
the FLG due to the 7-ms deglitch timeout. The 7-ms timeout is also applicable for Over-current recovery and Thermal recovery. The
AP2141D/AP2151D are designed to eliminate erroneous Over-current reporting without the need for external components, such as an RC delay
network.
with a 0.01-μF to 0.1-μF ceramic capacitor improves the immunity of the device to short-circuit transients. This capacitor also prevents the output
applications. Such implementations require the control of current surges as seen by the main power supply and the card being inserted. The most
start-up to devices being hot-plugged into a powered system. The UVLO feature of the AP2141D/AP2151D also ensures that the switch is off after
the card has been removed, and that the switch is off during the next insertion.
By placing the AP2141D/AP2151D between the VCC input and the rest of the circuitry, the input power reaches these devices first after insertion.
The typical rise time of the switch is approximately 1ms, providing a slow voltage ramp at the output of the device. This implementation controls the
system surge current and provides a hot-plugging mechanism for any device.
Application Information
Special Functions:
Discharge Function
When enable is de-asserted, the discharge function is active. The output capacitor is discharged through an internal NMOS that has a discharge
FLG Response
The FLG open-drain output goes active low for any of the two conditions: Over-Current or Over-Temperature. The time from when a fault condition is
encountered to when the FLG output goes low is 7-ms (typ). The FLG output remains low until both over-current and over-temperature conditions
Power Supply Considerations
A 0.01-μF to 0.1-μF X7R or X5R ceramic bypass capacitor between IN and GND, close to the device, is recommended. This limits the input voltage
drop during line transients. Placing a high-value electrolytic capacitor on the input (10-μF minimum) and output pin(s) is recommended when the
output load is heavy. This precaution also reduces power-supply transients that may cause ringing on the input. Additionally, bypassing the output
from going negative during turn-off due to inductive parasitics.
Power Dissipation and Junction Temperature
The low on-resistance of the internal MOSFET allows the small surface-mount packages to pass large current. Using the maximum operating
ambient temperature (T
The junction temperature can be calculated by:
Where:
Generic Hot-Plug Applications
In many applications it may be necessary to remove modules or PC boards while the main unit is still operating. These are considered hot-plug
effective way to control these surges is to limit and slowly ramp up the current and voltage being applied to the card, similar to the way in which a
power supply normally turns on. Due to the controlled rise and fall times of the AP2141D/AP2151D, these devices can be used to provide a softer
AP2141D/ AP2151D
Document number: DS32242 Rev. 3 - 2
P
T
R
P
T
J
A
D
D
θJA
= Ambient temperature °C
= P
= R
= Total power dissipation
= Thermal resistance
D
DS(ON)
x R
 JA
× I
+ T
2
A
) and R
A
DS(ON)
, the power dissipation can be calculated by:
(cont.)
www.diodes.com
11 of 18
AP2141D/ AP2151D
© Diodes Incorporated
March 2013