MAX8586ETA-T Maxim Integrated, MAX8586ETA-T Datasheet
MAX8586ETA-T
Specifications of MAX8586ETA-T
Related parts for MAX8586ETA-T
MAX8586ETA-T Summary of contents
Page 1
... MAX8586ETA -40°C to +85°C MAX8586ETA+ -40°C to +85°C MAX8586ETA+T -40°C to +85°C MAX8586ETA/V+ -40°C to +85°C /V denotes an automotive qualified part. + Denotes a lead(Pb)-free/RoHS-compliant package Tape and reel. Pin Configuration appears at end of data sheet. For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’ ...
Page 2
... A 2.3 2.5 1.2 1.4 0.800 0.925 0.5 0.6 = 26kΩ 1.35 1.75 ISET = 39kΩ 1.2 ISET = 60kΩ 0.74 ISET = 26kΩ 0.55 ISET = 39kΩ 0.37 ISET = 60kΩ 0.23 ISET -40°C to +85°C. MAX UNITS 5.50 V mΩ µA 55 µA 1 µA 2.7 V 1.6 1.050 A 0.7 2.20 A (Peak) A (RMS Maxim Integrated ...
Page 3
... Auto-Restart Threshold Auto-Restart Delay Note 1: All devices are 100% production tested at T design. Note 2: The output voltage at which the device transitions from short-circuit current limit to continuous current limit. Maxim Integrated Single 1.2A USB Switch in = 26kΩ to GND 100kΩ pullup to V FAULT ...
Page 4
... TEMPERATURE (°C) CURRENT LIMIT vs. TEMPERATURE 1.50 1.48 1.46 1.44 1.42 1.40 1.38 1.36 1. 1.32 1. -40 -15 10 TEMPERATURE (°C) SWITCH OFF-TIME vs. TEMPERATURE MEASURED FROM ON LOW UNTIL V FALLS TO 10% OF THE INPUT OUT -40 -15 10 TEMPERATURE (° ENRESET 5Ω LOAD Maxim Integrated ...
Page 5
... OVERLOAD RESPONSE INTO 2Ω FAULT OUT FAULT REMOVED V OUT 10ms/div SWITCH TURN-ON WAVEFORM INTO NO LOAD V OUT V ON 1ms/div Maxim Integrated Single 1.2A USB Switch in Typical Operating Characteristics (continued 5V +25°C, unless otherwise noted.) SEL ENRESET A AUTO-RESTART CURRENT vs. TEMPERATURE ...
Page 6
... MAX8586 toc17 2V/div 2V/div MAX8586 toc19 5V/div 50mV/div 500mA/div 2V/div STARTUP INTO 10μF FAULT V IN AC-COUPLED I OUT V OUT 2ms/div UVLO RESPONSE WITH 50Ω LOAD FAULT OUT 4ms/div MAX8586 toc18 5V/div 50mV/div 20mA/div 2A/div MAX8586 toc20 5V/div 2V/div 2V/div Maxim Integrated ...
Page 7
... Auto-Restart Enable Input. Drive ENRESET high to enable auto-restart mode. Drive ENRESET low to disable 8 ENRESET auto-restart mode. — EP Exposed Pad. Connect the exposed pad to a large ground plane to improve thermal power dissipation. IN SEL ON GND Maxim Integrated Single 1.2A USB Switch in FUNCTION is 26kΩ to 60kΩ. ISET OSCILLATOR CHARGE 20ms PUMP UVLO TIMER ...
Page 8
... USB specifi- cations. The MAX8586 successfully powers USB loads with additional bypass capacitance and/or large start- up currents while protecting the upstream power source. No fault is reported if the switch brings up the load within the 20ms blanking period. Fault Indicator and Fault Blanking Maxim Integrated ...
Page 9
... Usually, the load inductance is relatively small, and the MAX8586’s input includes a substantial bulk capaci- tance from an upstream regulator as well as local Maxim Integrated Single 1.2A USB Switch in bypass capacitors, limiting overshoot. If severe ringing occurs because of large load inductance, clamp the MAX8586 output below +6V and above -0 ...
Page 10
... ENRESET FAULT SEL ON GND TOP VIEW TRANSISTOR COUNT: 2117 PROCESS: BiCMOS OUTPUT SUPPLY UP TO 1.2A OUT C2 1μF AUTO-RESTART ON/OFF ISET R2 26kΩ Pin Configuration SEL ISET MAX8586 TDFN Chip Information ENRESET GND FAULT OUT Maxim Integrated ...
Page 11
... For the latest package outline information and land patterns (footprints www.maximintegrated.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE 8 TQFN-EP Maxim Integrated Single 1.2A USB Switch in PACKAGE CODE OUTLINE NO. T833-2 ...
Page 12
... MO229 / WEEA 0.40±0.05 0.65 BSC MO229 / WEEC 0.30±0.05 0.65 BSC MO229 / WEEC 0.30±0.05 0.50 BSC MO229 / WEED-3 0.25±0.05 0.50 BSC MO229 / WEED-3 0.25±0.05 0.50 BSC MO229 / WEED-3 0.25±0.05 0.40 BSC - - - - 0.20±0.05 0.40 BSC - - - - 0.20±0.05 0.40 BSC - - - - 0.20±0.05 [(N/2)- 1.90 REF 1.95 REF 1.95 REF 2.00 REF 2.00 REF 2.00 REF 2.40 REF 2.40 REF 2.40 REF Maxim Integrated ...
Page 13
... Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed ...