MAX232ECWE-T Maxim Integrated, MAX232ECWE-T Datasheet - Page 9
![no-image](/images/no-image-200.jpg)
MAX232ECWE-T
Manufacturer Part Number
MAX232ECWE-T
Description
RS-232 Interface IC
Manufacturer
Maxim Integrated
Series
MAX202E, MAX203E, MAX205E, MAX206E, MAX207E, MAX208E, MAX211E, MAX213E, MAX232E, MAX241Er
Datasheet
1.MAX232ECD.pdf
(26 pages)
Specifications of MAX232ECWE-T
Data Rate
200 Kbps
Operating Supply Voltage
5 V
Supply Current
10 mA
Operating Temperature Range
0 C to + 70 C
Mounting Style
SMD/SMT
Function
Transmitter
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Number Of Drivers
2
Number Of I/os
8
Number Of Receivers
2
Propagation Delay Time Ns
3.5 us, 1 us
Shutdown
No
Maxim Integrated
The MAX202E–MAX213E, MAX232E/MAX241E consist of
three sections: charge-pump voltage converters,
drivers (transmitters), and receivers. These E versions
provide extra protection against ESD. They survive
±15kV discharges to the RS-232 inputs and outputs,
tested using the Human Body Model. When tested
according to IEC1000-4-2, they survive ±8kV contact-
discharges and ±15kV air-gap discharges. The rugged
E versions are intended for use in harsh environments
or applications where the RS-232 connection is
frequently changed (such as notebook computers). The
standard (non-“E”) MAX202, MAX203, MAX205–
MAX208, MAX211, MAX213, MAX232, and MAX241 are
recommended for applications where cost is critical.
The +5V to ±10V conversion is performed by dual
charge-pump voltage converters (Figure 4). The first
charge-pump converter uses capacitor C1 to double
the +5V into +10V, storing the +10V on the output filter
capacitor, C3. The second uses C2 to invert the +10V
Figure 3. Transition Slew-Rate Circuit
_______________Detailed Description
±15kV ESD-Protected, +5V RS-232 Transceivers
+5V
0.1μF
0.1μF
0.1μF
0V (+5V)
0V (+5V)
*
*
*
TRANSMITTER INPUT PULL-UP RESISTORS, ENABLE, AND SHUTDOWN ARE NOT PROVIDED ON THE MAX202E, MAX203E, AND MAX232E.
ENABLE AND SHUTDOWN ARE NOT PROVIDED ON THE MAX207E AND MAX208E.
+5V to ±10V Dual Charge-Pump
MINIMUM SLEW-RATE TEST CIRCUIT
C1+
C1-
C2+
C2-
T_IN
R_OUT
EN (EN)
SHDN (SHDN)
MAX202E–MAX213E, MAX232E/MAX241E
V
CC
400kΩ
MAX2_ _E
R_
V
T_
CC
Voltage Converter
T_OUT
R_IN
5kΩ
V+
V-
0.1μF
0.1μF
*
*
3kΩ
* 1μF FOR MAX232E/MAX241E
( ) ARE FOR MAX213E
2500pF
into -10V, storing the -10V on the V- output filter
capacitor, C4.
In shutdown mode, V+ is internally connected to V
a 1kΩ pull-down resistor, and V- is internally connected
to ground by a 1kΩ pull up resistor.
With V
is ±8V when loaded with a nominal 5kΩ RS-232
receiver. The output swing is guaranteed to meet
EIA/TIA-232E and V.28 specifications that call for ±5V
minimum output levels under worst-case conditions.
These include a 3kΩ load, minimum V
maximum operating temperature. The open-circuit
output voltage swings from (V+ - 0.6V) to V-.
Input thresholds are CMOS/TTL compatible. The
unused drivers’ inputs on the MAX205E–MAX208E,
MAX211E, MAX213E, and MAX241E can be left
unconnected because 400kΩ pull up resistors to V
are included on-chip. Since all drivers invert, the pull up
resistors force the unused drivers’ outputs low. The
MAX202E, MAX203E, and MAX232E do not have pull
up resistors on the transmitter inputs.
+5V
0.1μF
0.1μF
0.1μF
0V (+5V)
0V (+5V)
*
*
*
CC
= 5V, the typical driver output voltage swing
MAXIMUM SLEW-RATE TEST CIRCUIT
C1+
C1-
C2+
C2-
T_IN
R_OUT
EN (EN)
SHDN (SHDN)
V
CC
400kΩ
MAX2_ _E
V
T_
CC
R_
T_OUT
R_IN
5kΩ
V+
V-
0.1μF
0.1μF
*
*
RS-232 Drivers
7kΩ
50pF
CC
, and
CC
CC
by
9