CAT1163WI-42-T3 ON Semiconductor, CAT1163WI-42-T3 Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
CAT1163WI-42-T3
Manufacturer Part Number
CAT1163WI-42-T3
Description
Supervisory Circuits CPU Supervisor with 16K EEPROM
Manufacturer
ON Semiconductor
Datasheet
1.CAT1163LI45.pdf
(12 pages)
Specifications of CAT1163WI-42-T3
Product Category
Supervisory Circuits
Rohs
yes
Number Of Voltages Monitored
1
Monitored Voltage
3 V, 3.3 V, 5 V
Undervoltage Threshold
4.25 V
Overvoltage Threshold
4.5 V
Output Type
Active High, Active Low, Open Drain
Manual Reset
Resettable
Watchdog
Watchdog
Battery Backup Switching
No Backup
Power-up Reset Delay (typ)
270 ms
Supply Voltage - Max
6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
SOIC-8 Wide
Chip Enable Signals
No
Maximum Power Dissipation
1000 mW
Minimum Operating Temperature
- 40 C
Power Fail Detection
No
Supply Current (typ)
3000 uA
Supply Voltage - Min
2.7 V
WDI: WATCHDOG INPUT
1.6 seconds, the watchdog timer times out.
WP: WRITE PROTECT
Write Protected (READ only). When the pin is tied to GND
or left floating normal read/write operations are allowed to
the device.
RESET/RESET: RESET I/O
inputs. By forcing a reset condition on the pins the device
Reset Controller Description
correct system operation during brownout and power
up/down conditions. It is configured with open drain
RESET outputs. During power−up, the RESET outputs
remain active until V
continue driving the outputs for approximately 200 ms
(t
interval, the device will cease to drive the reset outputs. At
this point the reset outputs will be pulled up or down by their
respective pull up/down resistors. During power−down, the
RESET outputs will be active when V
The RESET outputs will be valid so long as V
(V
as a signal conditioning circuit for an externally applied
manual reset. The inputs are edge triggered; that is, the
PURST
If there is no transition on the WDI for more than
If the pin is tied to V
These are open drain pins and can be used as reset trigger
The CAT1163 precision RESET controller ensures
The RESET pins are I/Os; therefore, the CAT1163 can act
RVALID
RESET
) after reaching V
RESET
V
).
CC
V
RVALID
V
TH
CC
CC
reaches the V
the entire memory array becomes
TH
. After the t
TH
CC
threshold and will
falls below V
PURST
Figure 1. RESET Output Timing
CC
t
is > 1.0 V
PURST
DEVICE OPERATION
PIN DESCRIPTION
timeout
http://onsemi.com
TH
t
GLITCH
.
5
t
RPD
will initiate and maintain a reset condition. The RESET pin
must be connected through a pulldown resistor, and the
RESET pin must be connected through a pull−up resistor.
SDA: SERIAL DATA ADDRESS
all data into and out of the device. The SDA pin is an open
drain output and can be wire−ORed with other open drain or
open collector outputs.
SCL: Serial Clock
RESET input in the CAT1163 will initiate a reset timeout
after detecting a low to high transition and the RESET input
in the CAT1163 will initiate a reset timeout after detecting
a high to low transition.
Watchdog Timer
for microcontrollers. During a system failure, the CAT1163
will respond with a reset signal after a time−out interval of
1.6 seconds for a lack of activity. The CAT1163 is designed
with the Watchdog Timer feature on the WDI input. If the
microcontroller does not toggle the WDI input pin within 1.6
seconds, the Watchdog Timer times out. This will generate
a reset condition on reset outputs. The Watchdog Timer is
cleared by any transition on WDI.
will not count and will stay cleared.
The bidirectional serial data/address pin is used to transfer
Serial clock input.
The Watchdog Timer provides an independent protection
As long as the reset signal is asserted, the Watchdog Timer
t
PURST
t
RPD