M95512-RMN6TP STMicroelectronics, M95512-RMN6TP Datasheet - Page 13
![IC EEPROM 512KBIT 2MHZ 8SOIC](/photos/1/38/13851/497-8-soic_sml.jpg)
M95512-RMN6TP
Manufacturer Part Number
M95512-RMN6TP
Description
IC EEPROM 512KBIT 2MHZ 8SOIC
Manufacturer
STMicroelectronics
Specifications of M95512-RMN6TP
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
512K (64K x 8)
Speed
2MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Density
512Kb
Interface Type
Serial (SPI)
Organization
64Kx8
Access Time (max)
150ns
Frequency (max)
2MHz
Write Protection
Yes
Data Retention
40Year
Operating Supply Voltage (typ)
2.5/3.3/5V
Operating Temp Range
-40C to 85C
Supply Current
3mA
Operating Supply Voltage (min)
1.8V
Operating Supply Voltage (max)
5.5V
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-6356-2
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M95512-RMN6TP
Manufacturer:
TDK
Quantity:
324
M95512-W, M95512-R, M95512-DR
4.1.4
4.2
4.3
Power-down
During power-down (continuous decrease in V
defined in
●
●
Active Power and Standby Power modes
When Chip Select (S) is low, the device is selected, and in the Active Power mode. The
device consumes I
When Chip Select (S) is high, the device is deselected. If a Write cycle is not currently in
progress, the device then goes in to the Standby Power mode, and the device consumption
drops to I
Hold condition
The Hold (HOLD) signal is used to pause any serial communications with the device without
resetting the clocking sequence.
During the Hold condition, the Serial Data Output (Q) is high impedance, and Serial Data
Input (D) and Serial Clock (C) are Don’t Care.
To enter the Hold condition, the device must be selected, with Chip Select (S) low.
Normally, the device is kept selected, for the whole duration of the Hold condition.
Deselecting the device while it is in the Hold condition, has the effect of resetting the state of
the device, and this mechanism can be used if it is required to reset any processes that had
been in progress.
The Hold condition starts when the Hold (HOLD) signal is driven low at the same time as
Serial Clock (C) already being low (as shown in
The Hold condition ends when the Hold (HOLD) signal is driven high at the same time as
Serial Clock (C) already being low.
Figure 5
with Serial Clock (C) being low.
Figure 5.
HOLD
deselected (Chip Select (S) should be allowed to follow the voltage applied on V
in Standby Power mode (that is there should not be any internal write cycle in
progress).
C
also shows what happens if the rising and falling edges are not timed to coincide
CC1
Table 8
Hold condition activation
.
and
CC
, as specified in
Table
10), the device must be:
Doc ID 11124 Rev 12
Condition
Hold
Table
15.
CC
Figure
below the minimum V
5).
Condition
Hold
CC
Operating features
operating voltage
CC
AI02029D
13/47
)