MAX6710BUT-T Maxim Integrated, MAX6710BUT-T Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
MAX6710BUT-T
Manufacturer Part Number
MAX6710BUT-T
Description
Supervisory Circuits
Manufacturer
Maxim Integrated
Series
MAX6700, MAX6710r
Datasheet
1.MAX6710PUT-T.pdf
(9 pages)
Specifications of MAX6710BUT-T
Number Of Voltages Monitored
4
Monitored Voltage
1.8 V, 2.5 V, 3 V, 3.3 V, 5 V
Undervoltage Threshold
4.5 V, 3 V, 2.25 V, Adjustable
Overvoltage Threshold
4.75 V, 3.15 V, 2.38 V, Adjustable
Output Type
Active Low, Open Drain
Manual Reset
Resettable
Watchdog
No Watchdog
Battery Backup Switching
No Backup
Power-up Reset Delay (typ)
200 ms
Supply Voltage - Max
5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
SOT-23
Chip Enable Signals
No
Maximum Power Dissipation
695.7 mW
Minimum Operating Temperature
- 40 C
Power Fail Detection
No
Supply Voltage - Min
1 V
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MAX6710BUT-T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Figure 3.
Figure 4. Interfacing to Different Logic-Supply Voltage
Figure 5. Setting the Auxiliary Monitor
Voltage µP Supervisory Circuits in SOT Package
RESET
V
IN_
TH_
RESET Output Timing Diagram
IN2 = +3.3V
MAX6700
MAX6710
IN2
GND
V
t
RD
INTH
R1
R2
_______________________________________________________________________________________
RESET
Low-Voltage, High-Accuracy, Triple/Quad
10%
100kΩ
V
REF
RESET
= 0.62V
R1 = R2
GND
+5V
V
t
RP
CC
(
V
0.62V
INTH
V
TH_
- 1
)
90%
V
monitored voltage. IN2 powers all other options for the
MAX6710 and is a monitored voltage. When any supply
drops below its threshold, the reset output asserts low
and remains low while either IN1 or IN2 is above 1.0V.
The MAX6700/MAX6710 offer several monitor options
with adjustable reset thresholds. The threshold voltage at
each adjustable IN_ input is typically 0.62V. To monitor a
voltage > 0.62V, connect a resistor-divider network to the
circuit as shown in Figure 5.
or, solved in terms of R1:
Because the MAX6700/MAX6710 have a guaranteed
input current of ±0.2µA (±0.4µA for IN1) on their
adjustable inputs, resistor values up to 100kΩ can be
used for R2 with < 1% error. The MAX6700/MAX6710Q
include an internal voltage clamp (1.5V typ) at each of
the adjustable voltage inputs. An input voltage higher
than 1.5V induces a higher input current.
Connect unused monitor inputs to a supply voltage
greater in magnitude than their specified threshold volt-
ages. For unused IN_ adjustable inputs, connect a 1MΩ
series resistor between the unused input and IN2 (or
V
tion (device power-supply pin). Do not connect unused
monitor inputs to ground or allow them to float.
Figure 6 shows an application circuit adding manual reset
to the MAX6710. Depressing the pushbutton switch short-
circuits the analog input to ground and initiates a RESET
pulse. The switch must be open for at least 140ms in
order to deassert the RESET output. No external switch
debounce is required. Use a small capacitor to improve
noise immunity when using long leads from the pushbut-
ton switch to the adjustable input.
The MAX6700/MAX6710 are normally powered from the
monitored IN2 or from the V
inputs are immune to short supply transients. For higher
immunity in noisy applications, connect a 0.1µF bypass
capacitor from the IN2 input to ground. Add capacitance
to IN1, IN3, and IN4 to increase their noise immunity.
CC
CC
) to limit the bias current. Use IN2 for normal opera-
Power-Supply Bypassing and Grounding
powers the MAX6700/MAX6710Q and is not a
V
R1 = R2 ((V
INTH
Adding Manual Reset Capability
= 0.62V x (R1 + R2) / R2
INTH
CC
Adjustable Thresholds
/ 0.62V) - 1)
supply input. All monitored
Unused Inputs
(MAX6710)
7