CY7C1320BV18-250BZC Cypress Semiconductor Corp, CY7C1320BV18-250BZC Datasheet - Page 6

• Manufacturer Part Number: CY7C1320BV18-250BZC
• Description: IC SRAM 18MBIT 250MHZ 165LFBGA
• Manufacturer: Cypress Semiconductor Corp

Specifications of CY7C1320BV18-250BZC

• Format - Memory: RAM
• Memory Type: SRAM - Synchronous, DDR II
• Memory Size: 18M (512K x 36)
• Speed: 250MHz
• Interface: Parallel
• Voltage - Supply: 1.7 V ~ 1.9 V
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 165-LFBGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Pin Definitions
Document Number: 38-05621 Rev. *D
DQ
LD
NWS
NWS
BWS
BWS
BWS
BWS
A, A0
R/W
C
C
K
K
Pin Name
[x:0]
0
1
2
3
0
1
,
,
,
,
Input Output-
Synchronous
Synchronous
Synchronous
Synchronous
Synchronous
Synchronous
Input Clock
Input Clock
Input Clock
Input Clock
Input-
Input-
Input-
Input-
Input-
IO
Data Input Output Signals. Inputs are sampled on the rising edge of K and K clocks during valid write
operations. These pins drive out the requested data during a read operation. Valid data is driven out on
the rising edge of both the C and C clocks during read operations or K and K when in single clock mode.
When read access is deselected, Q
CY7C1316BV18 − DQ
CY7C1916BV18 − DQ
CY7C1318BV18 − DQ
CY7C1320BV18 − DQ
Synchronous Load. This input is brought LOW when a bus cycle sequence is defined. This definition
includes address and read/write direction. All transactions operate on a burst of 2 data.
Nibble Write Select 0, 1 − Active LOW (CY7C1316BV18 only). Sampled on the rising edge of the K
and K clocks during write operations. Used to select which nibble is written into the device during the
current portion of the write operations. Nibbles not written remain unaltered.
NWS
All the Nibble Write Selects are sampled on the same edge as the data. Deselecting a Nibble Write Select
ignores the corresponding nibble of data and it is not written into the device.
Byte Write Select 0, 1, 2, and 3 − Active LOW. Sampled on the rising edge of the K and K clocks during
write operations. Used to select which byte is written into the device during the current portion of the Write
operations. Bytes not written remain unaltered.
CY7C1916BV18 − BWS
CY7C1318BV18 − BWS
CY7C1320BV18 − BWS
D
All the Byte Write Selects are sampled on the same edge as the data. Deselecting a Byte Write Select
ignores the corresponding byte of data and it is not written into the device.
Address Inputs. These address inputs are multiplexed for both read and write operations. Internally, the
device is organized as 2M x 8 (2 arrays each of 1M x 8) for CY7C1316BV18 and 2M x 9 (2 arrays each
of 1M x 9) for CY7C1916BV18, a single 1M x 18 array for CY7C1916BV18, and a single array of 512K x
36 for CY7C1318BV18.
CY7C1316BV18 – Because the least significant bit of the address internally is a ‘0’, only 20 external
address inputs are needed to access the entire memory array.
CY7C1916BV18 – Because the least significant bit of the address internally is a ‘0’, only 20 external
address inputs are needed to access the entire memory array.
CY7C1318BV18 – A0 is the input to the burst counter. These are incremented internally in a linear fashion.
20 address inputs are needed to access the entire memory array.
CY7C1320BV18 – A0 is the input to the burst counter. These are incremented internally in a linear fashion.
19 address inputs are needed to access the entire memory array. All the address inputs are ignored when
the appropriate port is deselected.
Synchronous Read/Write Input. When LD is LOW, this input designates the access type (read when
R/W is HIGH, write when R/W is LOW) for the loaded address. R/W must meet the setup and hold times
around the edge of K.
Positive Input Clock for Output Data. C is used in conjunction with C to clock out the read data from
the device. C and C can be used together to deskew the flight times of various devices on the board back
to the controller. See
Negative Input Clock for Output Data. C is used in conjunction with C to clock out the read data from
the device. C and C can be used together to deskew the flight times of various devices on the board back
to the controller. See
Positive Input Clock Input. The rising edge of K is used to capture synchronous inputs to the device
and to drive out data through Q
edge of K.
Negative Input Clock Input. K is used to capture synchronous data being presented to the device and
to drive out data through Q
[35:27]
0
controls D
.
[3:0]
and NWS
Application Example
Application Example
[7:0]
[8:0]
[17:0]
[35:0]
0
0
0
controls D
controls D
controls D
[x:0]
1
when in single clock mode.
[x:0]
controls D
[8:0]
when in single clock mode. All accesses are initiated on the rising
[x:0]
[8:0]
[8:0]
, BWS
are automatically tri-stated.
and BWS
on page 9 for more information.
on page 9 for more information.
[7:4]
Pin Description
1
.
controls D
CY7C1316BV18, CY7C1916BV18
CY7C1318BV18, CY7C1320BV18
1
controls D
[17:9]
, BWS
[17:9].
2
controls D
[26:18]
and BWS
Page 6 of 31
3
controls
[+] Feedback