24LC16BH-E/P Microchip Technology, 24LC16BH-E/P Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
24LC16BH-E/P
Manufacturer Part Number
24LC16BH-E/P
Description
IC EEPROM 16KBIT 400KHZ 8DIP
Manufacturer
Microchip Technology
Datasheets
1.24LC16BT-IST.pdf
(22 pages)
2.24LC16BHT-IOT.pdf
(28 pages)
3.24LC16BH-ESN.pdf
(26 pages)
Specifications of 24LC16BH-E/P
Memory Size
16K (2K x 8)
Package / Case
8-DIP (0.300", 7.62mm)
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Speed
400kHz
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Organization
8 Block x 256 x 8
Interface Type
I2C
Maximum Clock Frequency
0.4 MHz
Access Time
900 ns
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.5 V
Maximum Operating Current
3 mA
Maximum Operating Temperature
+ 125 C
Mounting Style
Through Hole
Minimum Operating Temperature
- 40 C
Operating Supply Voltage
3.3 V, 5 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
8.0
The descriptions of the pins are listed in Table 8-1.
TABLE 8-1:
8.1
SDA is a bidirectional pin used to transfer addresses
and data into and out of the device. Since it is an open-
drain terminal, the SDA bus requires a pull-up resistor
to V
For normal data transfer, SDA is allowed to change
only during SCL low. Changes during SCL high are
reserved for indicating Start and Stop conditions.
8.2
The SCL input is used to synchronize the data transfer
to and from the device.
© 2008 Microchip Technology Inc.
Name
SDA
SCL
V
CC
V
WP
A0
A1
A2
CC
SS
(typical 10 kΩ for 100 kHz, 2 kΩ for 400 kHz).
PIN DESCRIPTIONS
Serial Address/Data Input/Output
(SDA)
Serial Clock (SCL)
PDIP
1
2
3
4
5
6
7
8
PIN FUNCTION TABLE
SOIC
1
2
3
4
5
6
7
8
TSSOP
1
2
3
4
5
6
7
8
TDFN
1
2
3
4
5
6
7
8
8.3
The WP pin must be connected to either V
If tied to V
(read/write the entire memory 000h-7FFh).
If tied to V
memory will be write-protected (400h-7FFh). Read
operations are not affected.
8.4
The A0, A1 and A2 pins are not used by the 24XX16H.
They may be left floating or tied to either V
24AA16H/24LC16BH
MSOP
1
2
3
4
5
6
7
8
Write-Protect (WP)
A0, A1, A2
CC
SS
, write operations are inhibited, half of the
SOT-23
, normal memory operation is enabled
—
—
—
2
3
1
5
4
Not Connected
Not Connected
Not Connected
Ground
Serial Address/Data I/O
Serial Clock
Write-Protect Input
+1.7V to 5.5V Power Supply
Description
DS22118A-page 11
SS
SS
or V
or V
CC
CC
.
.