24LC22A-I/SN Microchip Technology, 24LC22A-I/SN Datasheet - Page 4

no-image

24LC22A-I/SN

Manufacturer Part Number
24LC22A-I/SN
Description
IC EEPROM 2KBIT 400KHZ 8SOIC
Manufacturer
Microchip Technology
Datasheets

Specifications of 24LC22A-I/SN

Memory Size
2K (256 x 8)
Package / Case
8-SOIC (3.9mm Width)
Operating Temperature
-40°C ~ 85°C
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Speed
100kHz, 400kHz
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.5 V ~ 5.5 V
Organization
256 K x 8
Interface Type
2-Wire
Maximum Clock Frequency
0.1 MHz
Access Time
10 ms
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.5 V
Maximum Operating Current
3 mA
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Operating Supply Voltage
2.5 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
24LC22A-I/SNG
24LC22A-I/SNG
24LC22AI/SN

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
24LC22A-I/SN
Manufacturer:
MICR
Quantity:
20 000
24LC22A
2.0
The 24LC22A is designed to comply to the DDC Stan-
dard proposed by VESA (Figure 3-3) with the exception
that it is not Access.bus capable. It operates in two
modes, the Transmit-Only mode (1 Kbit) and the
Bidirectional mode (2 Kbit). There is a separate 2-wire
protocol to support each mode, each having a separate
clock input but sharing a common data line (SDA). The
device enters the Transmit-Only mode upon power-up.
In this mode, the device transmits data bits on the SDA
pin in response to a clock signal on the VCLK pin. The
device will remain in this mode until a valid high-to-low
transition is placed on the SCL input. When a valid tran-
sition on SCL is recognized, the device will switch into
the Bidirectional mode and look for its control byte to be
sent by the master. If it detects its control byte, it will
stay in the Bidirectional mode. Otherwise, it will revert
to the Transmit-Only mode after it sees 128 VCLK
pulses.
2.1
The device will power-up in the Transmit-Only mode at
address 00h. This mode supports a unidirectional
2-wire protocol for continuous transmission of the first
FIGURE 2-1:
FIGURE 2-2:
DS21683B-page 4
FUNCTIONAL DESCRIPTION
Transmit-Only Mode
VCLK
SDA
SCL
VCLK
Vcc
SCL
SDA
TRANSMIT-ONLY MODE
DEVICE INITIALIZATION
T
VAA
T
VHIGH
High-Impedance for 9 Clock Cycles
T
1
VPU
Bit 1 (LSB)
T
VLOW
2
T
VAA
Null Bit
8
1 Kbit of the memory array. This device requires that it
be initialized prior to valid data being sent in the Trans-
mit-Only mode (Section 2.2). In this mode, data is
transmitted on the SDA pin in 8-bit bytes, with each
byte followed by a ninth, Null bit (Figure 2-1). The clock
source for the Transmit-Only mode is provided on the
VCLK pin, and a data bit is output on the rising edge on
this pin. The eight bits in each byte are transmitted
Most Significant bit first. Each byte within the memory
array will be output in sequence. After address 7Fh in
the memory array is transmitted, the internal Address
Pointers will wrap-around to the first memory location
(00h) and continue. The Bidirectional mode Clock
(SCL) pin must be held high for the device to remain in
the Transmit-Only mode.
2.2
After V
Transmit-Only mode. Nine clock cycles on the VCLK
pin must be given to the device for it to perform internal
sychronization. During this period, the SDA pin will be
in a high-impedance state. On the rising edge of the
tenth clock cycle, the device will output the first valid
data bit which will be the Most Significant bit in address
00h. (Figure 2-2).
CC
9
Initialization Procedure
Bit 1 (MSB)
has stabilized, the device will be in the
T
VAA
10
Bit 8
© 2007 Microchip Technology Inc.
T
Bit 7
VAA
11
Bit 7

Related parts for 24LC22A-I/SN