AT25320B-XHL-T Atmel, AT25320B-XHL-T Datasheet

Page 1

... JEDEC SOIC, 8-lead UDFN, 8-lead XDFN, 8-lead TSSOP, and 8-ball VFBGA packages. The AT25320B/640B is enabled through the Chip Select pin (CS) and accessed via a three-wire interface consisting of Serial Data Input (SI), Serial Data Output (SO), and Serial Clock (SCK). All programming cycles are completely self-timed, and no sepa- rate erase cycle is required before write ...

Page 2

... Voltage on Any Pin with Respect to Ground..............................–1.0V to +7.0V Maximum Operating Voltage.................................... 6.25V DC Output Current ................................................. 5.0 mA Figure 1-1. Block Diagram Atmel AT25320B/640B 2 *NOTICE: Stresses beyond those listed under “Abso- lute Maximum Ratings” may cause perma- nent damage to the device. This is a stress ...

Page 3

... 3.0mA OL 3.6V  V  5. 1.6mA 0.15mA OL 1.8V  V  3. 100µ ° C Atmel AT25320B/640B = +5.0V (unless otherwise noted) CC Max Units +1.8V to +5.5V (unless otherwise noted) CC Min Typ Max 1.8 5.5 2.5 5.5 4.5 5.5 7.5 10.0 4.0 10.0 4 ...

Page 4

... Data In Setup Time SU t Data In Hold Time H t HOLD Setup Time HD t HOLD Hold Time CD t Output Valid V t Output Hold Time HO Atmel AT25320B/640B 4 = 40°C to +85° Specified, – Voltage Min 4.5–5.5 0 2.5–5.5 0 1.8–5.5 0 4.5–5.5 2.5–5.5 1.8– ...

Page 5

... CS is still low will interrupt a write to the status register. If the internal write cycle has already been initiated, WP going low will have no effect on any write operation to the status register. The WP pin function is blocked when the WPEN bit in the status register is “0”. This will allow the user to install the AT25320B/640B in a system with the 8535F–SEEPR–6/10 ...

Page 6

... WP pin tied to ground and still be able to write to the status register. All WP pin functions are enabled when the WPEN bit is set to “1”. Figure 2-1. SPI Serial Interface Atmel AT25320B/640B 6 AT25320B/640B 8535F–SEEPR–6/10 ...

Page 7

... The Atmel AT25320B/640B is designed to interface directly with the synchronous serial peripheral interface (SPI) of the 6805 and 68HC11 series of microcontrollers. The AT25320B/640B utilizes an 8-bit instruction register. The list of instructions and their operation codes are con- tained in Table 3-1. All instructions, addresses, and data are transferred with the MSB first and start with a high-to- low CS transition ...

Page 8

... X High X High READ SEQUENCE (READ): Reading the AT25320B/640B via the Serial Output (SO) pin requires the following sequence. After the CS line is pulled low to select a device, the read op-code is transmitted via the SI line followed by the byte address to be read (A15 The data (D7 D0) at the specified address is then shifted out onto the SO line. If only one byte read, the CS – ...

Page 9

... If Bit 0 = “1”, the write cycle is still in progress. If Bit 0 = “0”, the write cycle has ended. Only the RDSR instruction is enabled during the write programming cycle. The AT25320B/640B is capable of a 32-byte page write operation. After each byte of data is received, the five low- order address bits are internally incremented by one; the high-order bits of the address will remain constant. If more than 32-bytes of data are transmitted, the address counter will roll over and the previously written data will be overwritten ...

Page 10

... Timing Diagrams Figure 4-1. Synchronous Data Timing (for Mode CSS V IH SCK HI Figure 4-2. WREN Timing CS SCK SI SO Figure 4-3. WRDI Timing CS SCK SI SO Atmel AT25320B/640B VALID IN WREN OP-CODE HI-Z WRDI OP-CODE HI CSH t DIS HI-Z 8535F–SEEPR–6/10 ...

Page 11

... Figure 4-4. RDSR Timing SCK SI INSTRUCTION HIGH IMPEDANCE SO Figure 4-5. WRSR Timing SCK SI HIGH IMPEDANCE SO Figure 4-6. READ Timing SCK SI INSTRUCTION HIGH IMPEDANCE SO 8535F–SEEPR–6/ MSB INSTRUCTION BYTE ADDRESS ... 3 2 Atmel AT25320B/640B DATA OUT DATA DATA OUT MSB 11 ...

Page 12

... Figure 4-7. WRITE Timing SCK SI INSTRUCTION HIGH IMPEDANCE SO Figure 4-8. HOLD Timing CS SCK HOLD SO Atmel AT25320B/640B BYTE ADDRESS ... DATA 8535F–SEEPR–6/10 ...

Page 13

... Ordering Code Detail Atmel Designator Product Family Device Density 320 = 32-kilobit 640 = 64-kilobit Device Revision 8535F–SEEPR–6/ Atmel AT25320B/640B Shipping Carrier Option B or blank = Bulk (tubes Tape and reel Operating Voltage L = 1.8V to 5.5V Packaged Device Grade or Wafer/Die Thickness H = Green, NiPdAu lead finish Industrial Temperature range (-40° ...

Page 14

... Part Markings 6.1 Atmel AT25320B AT25320B-SSHL Top Mark |---|---|---|---|---|---|---|---| |---|---|---|---|---|---|---|---| |---|---|---|---|---|---|---|---| * |---|---|---|---|---|---|---|---| | PIN 1 INDICATOR (DOT) AT25320B-XHL Top Mark PIN 1 INDICATOR (DOT |---|---|---|---|---|---| A T |---|---|---|---|---|---| 5 B |---|---|---|---|---|---|---| ATMEL LOT NUMBER |---|---|---|---|---|---|---| AT25320B-MAHL Top Mark |---|---|---| 5 |---|---|---| H |---|---|---| Y |---|---|---| * | PIN 1 INDICATOR (DOT) Atmel AT25320B/640B 14 Seal Year | Seal Week @ = Country of Ass’ SEAL YEAR 6: 2006 ...

Page 15

... XX= TRACE CODE (ATMEL LOT NUMBER TO COORESPOND WITH TRACE CODE LOG BOOK) (e. AA, AB, AC,... YZ, ZZ ONE DIGIT YEAR CODE 4: 2004 7: 2007 5: 2005 8: 2008 6: 2006 9: 2009 Atmel AT25320B/640B WITH TRACE CODE LOG BOOK (e. AA, AB, AC,... AX, AY AZ) 0: 2010 1: 2011 2: 2012 3: 2013 M = SEAL MONTH (USE ALPHA DESIGNATOR A- JANUARY B = FEBRUARY " ...

Page 16

... PIN 1 INDICATOR (DOT) AT25640B-XHL Top Mark PIN 1 INDICATOR (DOT |---|---|---|---|---|---| A T |---|---|---|---|---|---| 5 C |---|---|---|---|---|---|---| ATMEL LOT NUMBER |---|---|---|---|---|---|---| AT25640B-MAHL Top Mark |---|---|---| 5 |---|---|---| H |---|---|---| Y |---|---|---| * | PIN 1 INDICATOR (DOT) Atmel AT25320B/640B 16 Seal Year | Seal Week @ = Country of Ass’ SEAL YEAR 6: 2006 2007 8: 2008 2009 @ = Country of Ass’ SEAL YEAR 8: 2008 ...

Page 17

... XX= TRACE CODE (ATMEL LOT NUMBER TO COORESPOND WITH TRACE CODE LOG BOOK) (e. AA, AB, AC,... YZ, ZZ ONE DIGIT YEAR CODE 4: 2004 7: 2007 5: 2005 8: 2008 6: 2006 9: 2009 Atmel AT25320B/640B WITH TRACE CODE LOG BOOK (e. AA, AB, AC,... AX, AY AZ) 0: 2010 1: 2011 2: 2012 3: 2013 M = SEAL MONTH (USE ALPHA DESIGNATOR A- JANUARY B = FEBRUARY " ...

Page 18

... Ordering Codes Atmel AT25320B Ordering Information Ordering Code (1) AT25320B-SSHL-B (NiPdAu Lead Finish) (2) AT25320B-SSHL-T (NiPdAu Lead Finish) (1) AT25320B-XHL-B (NiPdAu Lead Finish) (2) AT25320B-XHL-T (NiPdAu Lead Finish) (2) AT25320B-MAHL-T (NiPdAu Lead Finish) (2) AT25320B-MEHL-T (NiPdAu Lead Finish) (2) AT25320B-CUL-T (SnAgCu Ball Finish) (3) AT25320B-WWU11L Note: 1. Bulk delivery in tubes (SOIC and TSSOP 100/tube) 2 ...

Page 19

... Body, 0.50mm Pitch, Ultra Thin Mini-MAP, Dual No Lead Package (UDFN), (MLP 8MA2 2x3mm) 8ME1 8-lead (1.8mm x 2.2mm Body) Ultra Leadframe Land Grid Array (XDFN) 8U2-1 8-lead, 8.35mm x 3.73mm Body, 0.75mm Pitch, VFBGA Package (VFBGA) 8535F–SEEPR–6/10 Atmel AT25320B/640B Voltage Package 1.8V to 5.5V 8S1 1.8V to 5.5V 8S1 1.8V to 5.5V 8A2 1 ...

Page 20

... JEDEC SOIC TOP VIEW TOP VIEW e e SIDE VIEW SIDE VIEW Notes: This drawing is for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. Package Drawing Contact: packagedrawings@atmel.com Atmel AT25320B/640B TITLE 8S1, 8-lead (0.150” Wide Body), Plastic Gull ...

Page 21

... Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and determined at Datum Plane H. Package Drawing Contact: packagedrawings@atmel.com 8535F–SEEPR–6/ TITLE 8A2, 8-lead 4.4mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Atmel AT25320B/640B L1 L End View COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX D 2.90 3 ...

Page 22

... The terminal # laser-marked feature. 3. Dimensions b applies to metalized terminal and is measured between 0.15 mm and 0.30 mm from the terminal tip. If the terminal has the optional radius on the other end of the terminal, the dimension should not be measured in that radius area. Package Drawing Contact: packagedrawings@atmel.com Atmel AT25320B/640B Pin ...

Page 23

... PIN # Top View Package Drawing Contact: packagedrawings@atmel.com 8535F–SEEPR–6/ Side View TITLE 8ME1, 8-lead (1.80 x 2.20 mm Body) Extra Thin DFN (XDFN) Atmel AT25320B/640B e1 b PIN # Bottom View COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A – – 0.40 A1 0.00 – ...

Page 24

... VFBGA A1 Ball Pad Corner e (e1) Notes: 1. This drawing is for general information. 2. Dimension 'b' is measured at the maximum solder ball diameter. 3. Solder ball composition shall be 95.5Sn-4.0Ag-.5Cu. Package Drawing Contact: packagedrawings@atmel.com Atmel AT25320B/640B 24 0.10 (4X Top View A1 BALL PAD CORNER (d1) Bottom View 8 SOLDER BALLS TITLE 8U2-1, 8 ball, 2 ...

Page 25

... Comments Update 8A2 and 8S1 package drawings Remove Preliminary Update Ordering Code Detail, Ordering Information, template Change Catalog Numbering Add new Part Marking Information Add Part Marking information; changed to Preliminary status. Modify ‘Endurance’ parameter on page 6. Initial document release. Atmel AT25320B/640B 25 ...

Page 26

... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...