25AA040A-I/P Microchip Technology, 25AA040A-I/P Datasheet

no-image

25AA040A-I/P

Manufacturer Part Number
25AA040A-I/P
Description
IC EEPROM 4KBIT 10MHZ 8DIP
Manufacturer
Microchip Technology
Datasheet

Specifications of 25AA040A-I/P

Memory Size
4K (512 x 8)
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Speed
10MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-DIP (0.300", 7.62mm)
Clock Frequency
10MHz
Supply Voltage Range
1.8V To 5.5V
Memory Case Style
DIP
No. Of Pins
8
Operating Temperature Range
-40°C To +85°C
Svhc
No SVHC (15-Dec-2010)
Package /
RoHS Compliant
Memory Configuration
512 X 8
Interface Type
Serial, SPI
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
25AA040A-I/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Device Selection Table
Features:
• Max. Clock 10 MHz
• Low-Power CMOS Technology:
• 512 x 8-Bit Organization
• Write Page mode (up to 16 bytes)
• Sequential Read
• Self-timed Erase and Write Cycles (5 ms max.)
• Block Write Protection:
• Built-in Write Protection:
• High Reliability:
• Temperature Ranges Supported:
• Pb-Free and RoHS Compliant
Pin Function Table
© 2009 Microchip Technology Inc.
25AA040A
25LC040A
CS
SO
WP
V
SI
SCK
HOLD
V
- Max. Write Current: 5 mA at 5.5V, 10 MHz
- Read Current: 5 mA at 5.5V, 10 MHz
- Standby Current: 5 μA at 5.5V
- Protect none, 1/4, 1/2 or all of array
- Power-on/off data protection circuitry
- Write enable latch
- Write-protect pin
- Endurance: 1,000,000 Erase/Write cycles
- Data retention: >200 years
- ESD protection: >4000V
- Industrial (I):
- Automotive (E):
SS
CC
Part Number
Name
Chip Select Input
Serial Data Output
Write-Protect
Ground
Serial Data Input
Serial Clock Input
Hold Input
Supply Voltage
-40°C to +85°C
-40°C to +125°C
V
CC
1.8-5.5V
2.5-5.5V
Function
4K SPI Bus Serial EEPROM
Range
25AA040A/25LC040A
Page Size
16 Bytes
16 Bytes
*25XX040A is used in this document as a generic part number for the
25AA040A and the 25LC040A.
Description:
The Microchip Technology Inc. 25XX040A* is a 4 Kbit
Serial Electrically Erasable Programmable Read-Only
Memory (EEPROM). The memory is accessed via a
simple Serial Peripheral Interface (SPI) compatible
serial bus. The bus signals required are a clock input
(SCK) plus separate data in (SI) and data out (SO)
lines. Access to the device is controlled through a Chip
Select (CS) input.
Communication to the device can be paused via the
hold pin (HOLD). While the device is paused, transi-
tions on its inputs will be ignored, with the exception of
Chip Select, allowing the host to service higher priority
interrupts.
The 25XX040A is available in standard packages
including 8-lead PDIP and SOIC, and advanced
and rotated TSSOP, 8-lead 2x3 DFN, and 6-lead
SOT-23.
Package Types (not to scale)
packages including 8-lead MSOP, 8-lead TSSOP
V
V
WP
WP
CS
CS
SO
SO
SCK
Temp. Ranges
SS
SS
V
SS
SI
TSSOP/MSOP
1
1
2
2
3
3
4
4
SOT-23
1
2
3
(ST, MS)
I, E
(OT)
I
6
5
4
HOLD
V
V
CS
SO
X-Rotated TSSOP
SO
CS
CC
DD
8
8
7
7
6
6
5
5
V
V
HOLD
HOLD
SCK
SCK
SI
SI
1
2
3
4
CC
CC
(X/ST)
P, MS, SN, ST, MC, OT
P, MS, SN, ST, MC, OT
V
WP
V
WP
CS
SO
CS
SO
Packages
SS
8
7
6
5
SS
SCK
SI
V
WP
1
2
3
4
PDIP/SOIC
1
2
3
4
SS
DFN
DS21827F-page 1
(P, SN)
(MC)
8
7
6
5
8
7
6
5
V
HOLD
SCK
SI
V
HOLD
SCK
SI
CC
CC

Related parts for 25AA040A-I/P

25AA040A-I/P Summary of contents

Page 1

... TSSOP, 8-lead 2x3 DFN, and 6-lead SOT-23. Package Types (not to scale) TSSOP/MSOP (ST, MS SOT-23 (OT SCK HOLD *25XX040A is used in this document as a generic part number for the 25AA040A and the 25LC040A. Packages P, MS, SN, ST, MC MS, SN, ST, MC, OT PDIP/SOIC (P, SN HOLD 7 7 HOLD HOLD 6 6 SCK SCK SCK ...

Page 2

... ELECTRICAL CHARACTERISTICS (†) Absolute Maximum Ratings V .............................................................................................................................................................................6.5V CC All inputs and outputs w.r.t. V ......................................................................................................... -0. Storage temperature .................................................................................................................................-65°C to 150°C Ambient temperature under bias ...............................................................................................................-40°C to 125°C ESD protection on all pins ..........................................................................................................................................4 kV † NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device ...

Page 3

... Total Endurance™ Model which can be obtained from our web site: www.microchip.com begins on the rising edge of CS after a valid write sequence and ends when the internal write cycle WC is complete. © 2009 Microchip Technology Inc. 25AA040A/25LC040A Industrial (I -40°C to +85°C A Automotive (E -40°C to +125°C A Min ...

Page 4

... TABLE 1-2: AC CHARACTERISTICS (CONTINUED) AC CHARACTERISTICS Param. Sym. Characteristic No HOLD Hold Time HOLD Low to Output HZ High HOLD High to Output HV Valid 20 T Internal Write Cycle Time WC (byte or page) 21 — Endurance Note 1: This parameter is periodically sampled and not 100% tested. 2: This parameter is not tested but ensured by characterization. For endurance estimates in a specific application, please consult the Total Endurance™ ...

Page 5

... SI HOLD FIGURE 1-2: SERIAL INPUT TIMING CS 2 Mode 1,1 Mode 0,0 SCK MSB in SO FIGURE 1-3: SERIAL OUTPUT TIMING SCK 13 MSB out SO SI © 2009 Microchip Technology Inc. 25AA040A/25LC040A High-impedance n Don’t Care High-impedance 14 Don’t Care LSB in 3 Mode 1,1 ...

Page 6

... FUNCTIONAL DESCRIPTION 2.1 Principles of Operation The 25XX040A is a 512-byte Serial EEPROM designed to interface directly with the Serial Peripheral Interface (SPI) port of many of today’s popular microcontroller families, including Microchip’s PIC microcontrollers. It may also interface with microcon- trollers that do not have a built-in SPI port by using dis- crete I/O lines programmed properly in firmware to match the SPI protocol ...

Page 7

... High-impedance SO © 2009 Microchip Technology Inc. 25AA040A/25LC040A HV Generator EEPROM Array Page Latches Y Decoder Sense Amp. R/W Control Read data from memory array beginning at selected address 011 Write data to memory array beginning at selected address 010 Reset the write enable latch (disable write operations) ...

Page 8

... FIGURE 2-2: BYTE WRITE SEQUENCE SCK Instruction+Address MSb FIGURE 2-3: PAGE WRITE SEQUENCE SCK Instruction+Address MSb SCK Data Byte DS21827F-page Lower Address Byte High-impedance Lower Address Byte Data Byte Twc Data Byte Data Byte Data Byte n (16 max © 2009 Microchip Technology Inc. ...

Page 9

... FIGURE 2-5: WRITE DISABLE SEQUENCE (WRDI) CS SCK SI SO © 2009 Microchip Technology Inc. 25AA040A/25LC040A The following is a list of conditions under which the write enable latch will be reset: • Power-up See • WRDI instruction successfully executed • WRSR instruction successfully executed • WRITE instruction successfully executed • ...

Page 10

... Read Status Register Instruction (RDSR) The Read Status Register instruction (RDSR) provides access to the STATUS register. See Figure 2-6 for the RDSR timing sequence. The STATUS register may be read at any time, even during a write cycle. The STATUS register is formatted as follows: ...

Page 11

... Table 2-3. FIGURE 2-7: WRITE STATUS REGISTER TIMING SEQUENCE (WRSR SCK Instruction Note: An internal write cycle (T WC sequence. © 2009 Microchip Technology Inc. 25AA040A/25LC040A TABLE 2-3: BP1 Data to STATUS Register High-impedance ...

Page 12

... Data Protection The following protection has been implemented to prevent inadvertent writes to the array: • The write enable latch is reset on power-up • A write enable instruction must be issued to set the write enable latch • After a byte write, page write or STATUS register write, the write enable latch is reset • ...

Page 13

... WP going low will not change or disable the write cycle. See Table 2-4 for the Write-Protect Functionality Matrix. © 2009 Microchip Technology Inc. 25AA040A/25LC040A 3.4 Serial Input (SI) The SI pin is used to transfer data into the device. It receives instructions, addresses and data. Data is latched on the rising edge of the serial clock ...

Page 14

... Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. DS21827F-page 14 Example: 25AA040A e 3 I/P 1L7 0627 Example: ...

Page 15

... Package Marking Information (continued) 8-Lead 2X3 DFN XXX YWW NN 6-Lead SOT-23 XXNN © 2009 Microchip Technology Inc. 25AA040A/25LC040A Example: 421 627 L7 Example: 32L7 DS21827F-page 15 ...

Page 16

... DS21827F-page 16 © 2009 Microchip Technology Inc. ...

Page 17

... Microchip Technology Inc. 25AA040A/25LC040A α φ β DS21827F-page 17 ...

Page 18

... DS21827F-page 18 © 2009 Microchip Technology Inc. ...

Page 19

... Microchip Technology Inc. 25AA040A/25LC040A φ I DS21827F-page 19 ...

Page 20

... DS21827F-page 20 I © 2009 Microchip Technology Inc. φ ...

Page 21

... Microchip Technology Inc. 25AA040A/25LC040A DS21827F-page 21 ...

Page 22

... DS21827F-page 22 © 2009 Microchip Technology Inc. ...

Page 23

... Microchip Technology Inc. 25AA040A/25LC040A I φ DS21827F-page 23 ...

Page 24

... APPENDIX A: REVISION HISTORY Revision B Corrections to Section 1.0, Electrical Characteristics. Revision C Added Packages SOT-23, DFN and X-rotated TSSOP; Revised AC Char., Params. 9, 10; Revised Package Legend. Revision D Removed Preliminary status; Replaced package drawings (Rev. AP); Revise Table 1-1, Param. D004, D007, D008; Revise Table 1-2, Param ,10. ...

Page 25

... To register, access the Microchip web site at www.microchip.com, click on Customer Change Notification and follow the registration instructions. © 2009 Microchip Technology Inc. 25AA040A/25LC040A CUSTOMER SUPPORT Users of Microchip products can receive assistance through several channels: • Distributor or Representative • ...

Page 26

... Telephone: (_______) _________ - _________ Application (optional): Would you like a reply? Y Device: 25AA040A/25LC040A Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs you find the organization of this document easy to follow? If not, why? 4 ...

Page 27

... Serial EEPROM, Industrial temp., MSOP package 25AA040AT-I/SN = 4k-bit, 16-byte page, 1.8V Serial EEPROM, Industrial temp., Tape & Reel, SOIC package 25LC040AT-I/SN = 4k-bit, 16-byte page, 2.5V Serial EEPROM, Industrial temp., Tape & Reel, SOIC package 25LC040AT-I/ST = 4k-bit, 16-byte page, 2.5V Serial EEPROM, Industrial temp., Tape & ...

Page 28

... NOTES: DS21827F-page 28 © 2009 Microchip Technology Inc. ...

Page 29

... REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...

Page 30

... Fax: 886-3-6578-370 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2009 Microchip Technology Inc. EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 ...

Related keywords