93LC86/P Microchip Technology, 93LC86/P Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
93LC86/P
Manufacturer Part Number
93LC86/P
Description
IC EEPROM 16KBIT 3MHZ 8DIP
Manufacturer
Microchip Technology
Specifications of 93LC86/P
Memory Size
16K (2K x 8 or 1K x 16)
Package / Case
8-DIP (0.300", 7.62mm)
Operating Temperature
0°C ~ 70°C
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Speed
2MHz, 3MHz
Interface
Microwire, 3-Wire Serial
Voltage - Supply
2.5 V ~ 6.0 V
Organization
1 K x 16 or 2 K x 8
Interface Type
Microwire
Maximum Clock Frequency
2 MHz
Supply Voltage (max)
6 V
Supply Voltage (min)
2.5 V
Maximum Operating Current
3 mA
Maximum Operating Temperature
+ 70 C
Mounting Style
Through Hole
Minimum Operating Temperature
0 C
Operating Supply Voltage
2.5 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
93LC86/P
Manufacturer:
Microchip
Quantity:
5 510
Part Number:
93LC86/P
Manufacturer:
MIC
Quantity:
20 000
4.0
TABLE 4-1:
4.1
A high level selects the device. A low level deselects
the device and forces it into Standby mode. However, a
programming cycle which is already initiated will be
completed, regardless of the CS input signal. If CS is
brought low during a program cycle, the device will go
into Standby mode as soon as the programming cycle
is completed.
CS must be low for 250 ns minimum (T
consecutive instructions. If CS is low, the internal
control logic is held in a Reset status.
4.2
The Serial Clock is used to synchronize the communi-
cation between a master device and the 93LC76/86.
Opcode, address and data bits are clocked in on the
positive edge of CLK. Data bits are also clocked out on
the positive edge of CLK.
CLK can be stopped anywhere in the transmission
sequence (at high or low level) and can be continued
anytime with respect to clock high time (T
clock low time (T
freedom in preparing opcode, address and data.
CLK is a “don't care” if CS is low (device deselected). If
CS is high, but Start condition has not been detected,
any number of clock cycles can be received by the
device without changing its status (i.e., waiting for Start
condition).
CLK cycles are not required during the self-timed
WRITE (i.e., auto erase/write) cycle.
2010 Microchip Technology Inc.
CS
CLK
DI
DO
V
ORG
PE
V
SS
CC
Name
PIN DESCRIPTIONS
Chip Select (CS)
Serial Clock (CLK)
Chip Select
Serial Data Clock
Serial Data Input
Serial Data Output
Ground
Memory Configuration
Program Enable
Power Supply
CKL
PIN FUNCTION TABLE
). This gives the controlling master
Function
CSL
) between
CKH
) and
After detection of a Start condition the specified number
of clock cycles (respectively low-to-high transitions of
CLK) must be provided. These clock cycles are
required to clock in all opcode, address, and data bits
before an instruction is executed (see Table 1-3
through Table 1-6 for more details). CLK and DI then
become “don't care” inputs waiting for a new Start
condition to be detected.
4.3
Data In is used to clock in a Start bit, opcode, address
and data synchronously with the CLK input.
4.4
Data Out is used in the Read mode to output data
synchronously with the CLK input (T
positive edge of CLK).
This pin also provides Ready/Busy status information
during erase and write cycles. Ready/Busy status infor-
mation is available when CS is high. It will be displayed
until the next Start bit occurs as long as CS stays high.
4.5
When ORG is connected to V
nization is selected. When ORG is tied to V
memory organization is selected. There is an internal
pull-up resistor on the ORG pin that will select x16
organization when left unconnected.
4.6
This pin allows the user to enable or disable the ability
to write data to the memory array. If the PE pin is
floated or tied to V
If the PE pin is tied to V
inhibited. There is an internal pull-up on this device that
enables programming if this pin is left floating.
Note:
Data In (DI)
Data Out (DO)
Organization (ORG)
Program Enable (PE)
CS must go low between consecutive
instructions, except when performing a
sequential read (Refer to Section 3.1
“READ” for more detail on sequential
reads).
CC
, the device can be programmed.
93LC76/86
SS
CC
, programming will be
, the x16 memory orga-
DS21131F-page 11
PD
SS
after the
, the x8