AT27C256R-70JU Atmel, AT27C256R-70JU Datasheet - Page 3

• Manufacturer Part Number: AT27C256R-70JU
• Description: IC OTP 256KBIT 70NS 32PLCC
• Manufacturer: Atmel

Specifications of AT27C256R-70JU

• Format - Memory: EPROMs
• Memory Type: OTP EPROM
• Memory Size: 256K (32K x 8)
• Speed: 70ns
• Interface: Parallel
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-PLCC
• Organization: 32 K x 8
• Access Time: 45 ns
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Maximum Operating Temperature: 85 C
• Interface Type: Parallel
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Capacitance, Input: 4 pF
• Capacitance, Output: 8 pF
• Current, Input, Leakage: ±1 μA
• Current, Operating: 20 mA (Read)
• Current, Output, Leakage: ±5
• Density: 256K
• Package Type: PLCC
• Temperature, Operating: -40 to +85 °C
• Time, Access: 70 ns
• Time, Address Setup: 2
• Time, Fall: 20 ns
• Time, Rise: 20 ns
• Voltage, Esd: 2000 V
• Voltage, Input, High: 5.5 V (Read)
• Voltage, Input, Low: 0.8 V (Read)
• Voltage, Output, High: 2.4 V (Read)
• Voltage, Output, Low: 0.4 V (Read)
• Voltage, Supply: 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

3. System Considerations
4. Block Diagram
5. Absolute Maximum Ratings*
Note:
0014M–EPROM–12/07
Temperature Under Bias................................ -55°C to +125°C
Storage Temperature ..................................... -65°C to +150°C
Voltage on Any Pin with
Respect to Ground .........................................-2.0V to +7.0V
Voltage on A9 with
Respect to Ground ......................................-2.0V to +14.0V
V
Respect to Ground .......................................-2.0V to +14.0V
PP
Supply Voltage with
1. Minimum voltage is -0.6V DC which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is
V
CC
+ 0.75V dc which may overshoot to +7.0 volts for pulses of less than 20 ns.
Switching between active and standby conditions via the Chip Enable pin may produce tran-
sient voltage excursions. Unless accommodated by the system design, these transients may
exceed datasheet limits, resulting in device non-conformance. At a minimum, a 0.1 µF high
frequency, low inherent inductance, ceramic capacitor should be utilized for each device. This
capacitor should be connected between the V
to the device as possible. Additionally, to stabilize the supply voltage level on printed circuit
boards with large EPROM arrays, a 4.7 µF bulk electrolytic capacitor should be utilized, again
connected between the V
close as possible to the point where the power supply is connected to the array.
CC
(1)
(1)
(1)
and Ground terminals. This capacitor should be positioned as
*NOTICE:
CC
Stresses beyond those listed under “Absolute Maxi-
mum Ratings” may cause permanent damage to
the device. This is a stress rating only and func-
tional operation of the device at these or any other
conditions beyond those indicated in the opera-
tional sections of this specification is not implied.
Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
and Ground terminals of the device, as close
AT27C256R
3