EVAL-AD7490SDZ Analog Devices, EVAL-AD7490SDZ Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
EVAL-AD7490SDZ
Manufacturer Part Number
EVAL-AD7490SDZ
Description
Data Conversion IC Development Tools evaluation control board.
Manufacturer
Analog Devices
Type
ADCr
Series
AD7490r
Datasheet
1.EVAL-AD7490SDZ.pdf
(28 pages)
Specifications of EVAL-AD7490SDZ
Rohs
yes
Product
Evaluation Boards
Tool Is For Evaluation Of
AD7490
Interface Type
SPI
Operating Supply Voltage
2.7 V to 5.25 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Factory Pack Quantity
1
Data Sheet
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
Table 4. Pin Function Descriptions
TSSOP
20
23
22
14, 21, 24
13 to 5,
3 to 1,
28 to 25
19
15
16
17
N/A
Pin No.
LFCSP
18
21
20
12, 19, 22
11 to 9,
7 to 2,
31 to 26,
24
17
13
14
15
EP
Figure 3. 28-Lead TSSOP Pin Configuration
AGND
NC = NO CONNECT
ALL NC PINS SHOULD BE
CONNECTED STRAIGHT TO AGND
V
V
V
V
V
V
V
V
V
V
V
V
IN
IN
NC
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
11
10
9
8
7
6
5
4
3
2
1
0
10
11
12
13
14
1
2
3
4
5
6
7
8
9
(Not to Scale)
Mnemonic
CS
REF
V
AGND
V
DIN
DOUT
SCLK
V
EPAD
AD7490
TOP VIEW
DD
IN
DRIVE
0 to V
IN
IN
15
28
27
26
25
24
23
22
21
20
19
18
17
16
15
V
V
V
V
AGND
REF
V
AGND
CS
DIN
NC
V
SCLK
DOUT
IN
IN
IN
IN
DD
DRIVE
12
13
14
15
IN
Description
Chip Select. Active low logic input. This input provides the dual function of initiating
conversions on the AD7490 and also frames the serial data transfer.
Reference Input for the AD7490. An external reference must be applied to this input. The
voltage range for the external reference is 2.5 V ± 1% for specified performance.
Power Supply Input. The V
range, V
Analog Ground. Ground reference point for all circuitry on the AD7490. All analog/digital input
signals and any external reference signal should be referred to this AGND voltage. All AGND pins
should be connected together.
Analog Input 0 through Analog Input 15. Sixteen single-ended analog input channels that are
multiplexed into the on chip track-and-hold. The analog input channel to be converted is
selected by using the address bits ADD3 through ADD0 of the control register. The address bits,
in conjunction with the SEQ and SHADOW bits, allow the sequence register to be programmed.
The input range for all input channels can extend from 0 V to REF
via the RANGE bit in the control register. Any unused input channels should be connected to
AGND to avoid noise pickup.
Data In. Logic input. Data to be written to the control register of the AD7490 is provided on this
input and is clocked into the register on the falling edge of SCLK (see the Control Register
section).
Data Out. Logic output. The conversion result from the AD7490 is provided on this output as a
serial data stream. The bits are clocked out on the falling edge of the SCLK input. The data
stream consists of four address bits indicating which channel the conversion result corresponds
to, followed by the 12 bits of conversion data, which is provided by MSB first. The output coding
can be selected as straight binary or twos complement via the CODING bit in the control
register.
Serial Clock. Logic input. SCLK provides the serial clock for accessing data from the part. This
clock input is also used as the clock source for the conversion process of the AD7490.
Logic Power Supply Input. The voltage supplied at this pin determines at what voltage the serial
interface of the AD7490 operates.
Exposed Pad. Connect exposed pad to GND.
DD
should be from 4.75 V to 5.25 V.
Rev. D | Page 7 of 28
DD
range for the AD7490 is from 2.7 V to 5.25 V. For the 0 V to 2 × REF
Figure 4. 32-Lead LFCSP Pin Configuration
V
V
V
V
V
V
NOTES
1. NC = NO CONNECT. ALL NC PINS
2. CONNECT EXPOSED PAD TO GND
NC
NC
IN
IN
IN
IN
IN
IN
SHOULD BE CONNECTED STRAIGHT
TO AGND.
8
7
6
5
4
3
1
2
3
4
5
6
7
8
(Not to Scale)
AD7490
TOP VIEW
IN
or 0 V to 2 × REF
24
23
22
21
20
19
18
17
V
NC
AGND
REF
V
AGND
CS
DIN
IN
DD
15
IN
IN
AD7490
as selected
IN