IS24C02D-2SLI-TR ISSI, Integrated Silicon Solution Inc, IS24C02D-2SLI-TR Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/3/347/issi__integrated_silicon_solution_inc_sml.jpg)
IS24C02D-2SLI-TR
Manufacturer Part Number
IS24C02D-2SLI-TR
Description
IC EEPROM 2KBIT 1MHZ 8MSOP
Manufacturer
ISSI, Integrated Silicon Solution Inc
Datasheet
1.IS24C02D-2GLI-TR.pdf
(21 pages)
Specifications of IS24C02D-2SLI-TR
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
2K (256 x 8)
Speed
1MHz
Interface
I²C, 2-Wire Serial
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
IS24C02D
WRITE OPERATIOn
byte Write
In the Byte Write mode, the Master device sends the Start
condition and the Slave address information (with the R/W
set to Zero) to the Slave device. After the Slave generates
an ACK, the Master sends a byte address that is written
into the address pointer of the IS24C02D. After receiving
another ACK from the Slave, the Master device transmits
the data byte to be written into the address memory
location. The IS24C02D acknowledges once more and
the Master generates the Stop condition, at which time the
device begins its internal programming cycle. While this
internal cycle is in progress, the device will not respond
to any request from the Master device.
Page Write
The IS24C02D is capable of 16-byte Page-Write operation.
A Page-Write is initiated in the same manner as a Byte
Write, but instead of terminating the internal Write cycle
after the first data byte is transferred, the Master device can
transmit up to 15 more bytes. After the receipt of each data
byte, the IS24C02D responds immediately with an ACK
on SDA line, and the four lower order data byte address
bits are internally incremented by one, while the higher
order bits of the data byte address remain constant. If a
byte address is incremented from the last byte of a page,
it returns to the first byte of that page. If the Master device
should transmit more than 16 bytes prior to issuing the
Stop condition, the address counter will “roll over,” and the
previously written data will be overwritten. Once all 16
bytes are received and the Stop condition has been sent
by the Master, the internal programming cycle begins. At
this point, all received data is written to the IS24C02D in a
single Write cycle. All inputs are disabled until completion
of the internal Write cycle.
Integrated Silicon Solution, Inc. — www.issi.com
Rev. C
07/30/09
Permanent Write Protection
The IS24C02D contains a permanent write protection
feature that is initiated by means of a software command.
After the command is transmitted, the protected area
becomes irreversibly read-only despite power removal and
re-application on the device.The address range of the 128
bytes of the array that is affected by this feature is 00h-7Fh.
Once enabled, the permanent protection is independent
of the status of the WP pin. (If WP is raised to High, the
entire array is read-only. If WP is low, the region 00h-7Fh
can still be read-only.)
The software command is initiated similarly to a normal
byte write operation; however, the slave address begins
with the bits 0110 (see Figure 5). The following three bits
are A2 - A0. The last bit of the slave address (R/W) is 0. If
the IS24C02D responds with ACK, the device has not yet
had its write-protection permanently enabled.To complete
the command, the Master must transmit a dummy address
byte, dummy data byte, and a Stop signal (see Figure 11).
The WP pin must be Low during this command. Before
resuming any other command, the internal write cycle
should be observed.
The status of the permanent write protection can be safely
determined without any changes by transmitting the same
Slave address as above, but with the last bit (R/W) set to
1 (see Figure 12). If the permanent write protection has
been enabled, the IS24C02D will not acknowledge any
slave address starting with bits 0110 (see Figure 5).
Acknowledge (ACK) Polling
The disabling of the inputs can be used to take advantage
of the typical Write cycle time. Once the Stop condition
is issued to indicate the end of the host's Write operation,
the IS24C02D initiates the internal Write cycle.ACK polling
can be initiated immediately. This involves issuing the Start
condition followed by the Slave address for aWrite operation.
If the IS24C02D is still busy with the Write operation, no
ACK will be returned. If the IS24C02D has completed the
Write operation, an ACK will be returned and the host can
then proceed with the next Read or Write operation.
7